RYTEC DG1215, Инструкция по установке и эксплуатации

Страница: 19 / 26

13
OPTIONAL PROGRAMS
NOTE: The Digital Gateway has one programmable
output (output 7), two programmable inputs
(inputs 24 and 26) and various other pro-
gram options built in. A description of each
available program follows. See SETTING
THE PROGRAM OPTIONS on page 15 for
programming instructions.
PROGRAM 1, OUTPUT 7
This output can tell you if the door is not closed, fully
open or about to close. When output 7 is turned on
115 vac will be available at terminal 7. This power can
be used to turn on a 115 vac relay which can indicate
where the door is or what it is about to do. The relay
can operate warning lights, horns or signal an energy
management system. Only one of the three options
available in Program 1 can be selected at a time.
Door Not Closed, P1 = LSC
Output 7 will be on when the door is not closed. (Not
on the "Close" limit switch). The output will be off when
the door is fully closed. (On the "Close" limit switch).
This is the factory default setting. It tells you the door
is not closed.
Door Open, P1 = LSO
Output 7 will be on when the door is fully open. (On
the "Open" limit switch). The output will be off when
the door is below the open position. (Off of the "Open"
limit switch). It tells you the door is fully open.
Delay to Close, P1 = dtC
When the door is signaled to close, output 7 will turn
on, the Delay to Close timer (dtC) will start, but output
6, which closes the door will not be on. When the
Delay to Close timer times out, output 6 will activate
and the door will close. Output 7 will remain on until
the door is completely closed. Maximum time is 15
seconds. This option tells you the door is about to
close.
PROGRAM 2, INPUT 24
This input can be used to place the Digital Gateway
into an inactive condition, operate the door manually or
automatically or open the door to a height below fully
open. Only one of the Program 2 options can be
selected at a time.
LOC Condition, P2 = LOC
When input 24 is on and the door is fully closed the
Digital Gateway will go into an inactive condition. No
inputs will be able to activate the door. The message
LOC will be on the display. Once the connection is
removed from the input, the system will be ready for
normal operation. This is the factory default Program 2
setting and can be used to "lock out" the door.
MAN-AUTO Selector Switch, P2 = SSA
If this option is selected, a manual-automatic two
position selector switch can be connected to input 24.
When the switch is in the MAN position (there is no
connection at terminal 24) the A/A and Auto Close
delay timers are disabled. The Auto and Loop inputs
are inactive when the door is closed, but will reverse
the door if it is closing or hold it open when it is fully
open.
When the switch is in the AUTO position (there is a
connection at input 24) the A/A Close Delay timer will
turn on and all inputs will operate normally.
This option allows you to operate the door manually or
automatically.
MAN-AUTO Selector Switch with Open and Close
Inactive in Auto, P2 = SSb
This option operates the same as the MAN-AUTO
option described in MAN-AUTO Selector Switch, P2 =
SSA, except in the Auto position the Open and Close
inputs are inactive.
Passage Entry—Timed, P2 = Pet
When this option is used and the door is activated to
open with input 24, it will open for a predetermined
time. This allows you to open the door part way with an
activator connected to terminal 24 while other activa-
tors connected to other inputs will open the door
completely. A 20 foot door could be opened 8–10 feet
for small loads and 20 feet for large loads.
When input 24 is activated while the door is fully
closed the door will open and the Passage timer (PEt)
will begin counting down. When the Passage timer
reaches zero the door will stop. Activating this input
again will close the door. If the A/A Close Delay timer
is on when the door is opened with input 24, the door
will open until the Passage timer reaches zero. Then
the A/A Close Delay timer will time out and close the
door.
OPTIONAL PROGRAMS