16
English(Original instructions)
refueling site before starting engine.
■ Stop the engine and allow to cool before refueling or
storing the product.
■ Allow the engine to cool; empty the fuel tank and
secure the product from moving before transporting in
a vehicle. Secure the unit during transport to prevent
damage or injury.
■ Debris, when hit by the line, can travel significant
distances. Remove debris from the working area
before operating.
■ When operating the product, wear hearing protection.
■ Operating similar tools nearby increases risk of injury.
■ Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay
extra attention to what is going on in the working area.
■ If working in an area where there is a risk of falling
objects, head protection must be worn.
WARNING
Inspection after dropping or other impacts:
Thoroughly inspect the product and identify any
affections or damage with it. Any part that is
damaged should be properly repaired or replaced
by an authorized service centre.
WARNING
Injuries may be caused, or aggravated, by
prolonged use of a tool. When using any tool for
prolonged periods, ensure you take regular breaks.
TRIMMER SAFETY WARNINGS
■ Replace the bump head if cracked, chipped, or
damaged in any way. Be sure the bump head is
properly installed and securely fastened. Failure to do
so can cause serious injury.
■ Make sure all guards, straps, deflectors and handles
are properly and securely attached.
■ Use only the manufacturer's replacement line in the
cutting head. Do not use any other cutting attachment.
Failure to do so can result in serious personal injury.
■ Never operate unit without the safety guard in place
and in good condition.
■ Maintain a firm grip on both handles while trimming.
Keep bump head below waist level. Never cut with the
bump head located over 76 cm above the ground.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and
the operator should pay special attention to avoid the
following:
■ Injury caused by vibration. Hold the tool by designated
handles and restrict working time and exposure.
■ Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
■ Eye injury due to flying debris. Wear eye protection
at all times.
DESCRIPTION
1. Primer Bulb
2. Choke Lever
3. Fuel Cap
4. Starter Grip
5. Throttle Lock
6. On / Off Switch
7. Throttle Trigger
8. Rear Handle
9. Front Handle
10. Shaft
11. Deflector
12. ReelEasyTM Line Trimmer Head
13. Cutting Line
14. Idle Speed Screw
15. Knob
16. Hanger Cap
17. Latch
18. Screw
19. Barrier
20. M-clamp, plastic
21. Wrench
ASSEMBLY
UNPACKING
This product requires assembly.
■ Carefully remove the tool and any accessories from
the box. Make sure that all items listed in the packing
list are included.
■ Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
Содержание RLT30CESC
