12
| English
TROUBLESHOOTING
Problem
Possible cause
Solution
Engine will not start (Make
sure ignition switch is in
start position “I”).
No spark.
The spark plug could be cracked or damaged.
Replace the old spark plug with a new one and
try to start again. If engine will still not start, return
the product to an authorised service centre for
further checking.
Flooded engine.
With the ignition switch off, remove spark plug.
Move choke lever to run position (pushed in
completely) and pull starter grip 15 to 20 times.
This will clear excess fuel from engine. Clean
and reinstall spark plug. Set ignition switch to
run (I) position. Push and fully release primer
bulb 10 times. Pull starter grip three times with
choke lever at run. If engine does not start, move
choke lever to choke and repeat normal starting
procedure. If engine still fails to start, repeat
procedure with a new spark plug.
Engine starts but will not
accelerate properly.
Carburettor requires “L” (Low jet)
adjustment.
Contact an authorised service centre for
carburettor adjustment.
Engine starts but will not run
roperly at high speed.
Carburettor requires “H” (High jet)
adjustment.
Contact an authorised service centre for
carburettor adjustment.
Engine does not reach
full speed and/or emits
excessive smoke.
Check lubricant fuel mixture.
Use fresh fuel and the correct 2-stroke lubricant
mix ratio.
Air
fi
lter dirty.
Clean the air
fi
lter.
Spark arrester screen dirty.
Contact an authorised service centre for service
or replacement.
Carburettor requires “H” (High jet)
adjustment.
Contact an authorised service centre for
carburettor adjustment.
Engine starts, runs, and
accelerates but will not idle.
Carburettor requires adjustment.
Contact an authorised service centre for
carburettor adjustment.
Engine starts and runs, but
chain is not rotating.
Chain lubricant tank empty.
Lubricant tank should be
fi
lled every time.
Check chain tension for overtight
condition.
Tension the chain.
Check for lubricating function.
Run at half throttle 30 to 45 seconds. Stop saw
and check for lubricant dripping from guide bar. If
lubricant is present, the chain may be dull or bar
may be damaged. If no lubricant is on the guide
bar, contact an authorised service centre.
Bar and chain running hot
and smoking.
Chain brake engaged.
Release the chain brake.
Chain tension too tight.
Tension the chain.
Check guide bar and chain for
damage.
Inspect the guide bar and chain for damage.
Engine dies during normal
operation and will not
restart.
Product set to anti-freeze mode
at normal temperatures.
Set the product to normal operating mode. Allow
the engine to cool down before restarting.
Engine will not start or does
not reach full speed.
Product set to anti-freeze mode
at normal temperatures.
Set the product to normal operating mode.
Engine does not reach full
speed at low temperatures.
Product set to normal mode at
low temperatures.
Set the product to anti-freeze mode.
Содержание RCS3835T
