RuggedCom RUGGEDBACKBONE RX5000 Скачать руководство пользователя | Manualshive

Страница: 292 / 440

background image

29. Layer 3 Switching

ROX™ v2.2 User Guide

292

RuggedBackbone™ RX5000

29.1.9. Sample Use Case

Consider the network illustrated below. The switch connecting all of these networks is a
RuggedBackbone™ Layer 3 switch.

Figure 29.2. Layer 3 Switch Use Case

Assume the following:

• VLAN 150 and VLAN 250 have approximately 200 devices each.

• VLAN 300 is a server farm with RuggedNMS and some other servers polling these devices on a

near-constant basis. The IP address for Server 1 is 172.30.30.10. The IP address for Server 2 is
172.30.30.20

• VLAN 400 connects the Layer 3 switch to an external network via a gateway with the IP address

172.30.40.2.

• Devices and servers in VLAN 150, 250 and 300 should only be able to reach 2 networks –

10.200.50.0/24 and 10.200.60.0/24 – for management purposes.

• The 400 devices in VLAN 150 and VLAN 250 receive IP multicast data from the external network

(VLAN 400) at the address 227.100.20.100.

• Servers in VLAN 300 receive IP multicast data from the external network (VLAN 400) at the address

227.100.250.250.

• No firewall is used in this use case.

Assume all Layer 2 switching-related configuration has been done; that is, the VLANs have been
created with proper port assignment. In this example, no specific Layer 3 switch configuration is explicitly
required. As long as a software router configuration is sufficient for the above requirements, the Layer
3 Switch will be able to function through auto-learning switching rules. However, the Layer 3 switching
configuration described in the following sections is recommended for better utilization of CPU and Layer
3 switching ASIC resources:

•

Section 29.1.9.1, “Setting up Unicast Routes”

•

Section 29.1.9.2, “Setting up Multicast Routing”

•

Section 29.1.9.3, “Configuring Static Layer 3 Switching Rules for Servers”

•

Section 29.1.9.4, “Configuring Static ARP Table Entries for Servers”

•

Section 29.1.9.5, “Layer 3 Switching Rules for Devices in VLANs 150 and 250”

«
...
290
291
292
293
294
...
»

Содержание RUGGEDBACKBONE RX5000

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RUGGEDBACKBONE RX5000

Бренд: 3Com Страницы: 20

Verizon DSL-2750B

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: PaloAlto Networks Страницы: 3

Бренд: F5 Страницы: 72

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: Opengear Страницы: 2

Бренд: BSS Audio Страницы: 20

Бренд: Aztech Страницы: 2

Бренд: IEI Technology Страницы: 86

Lite N42B1P Series

Бренд: Dahua Technology Страницы: 14

Бренд: axing Страницы: 52

Media Board D/120JCT-LS-EW

Бренд: Dialogic Страницы: 2

JetFusion 2100 Series

Бренд: Paradyne Страницы: 296

Бренд: Tripp Lite Страницы: 2

Airborne M2M ABDN-er-DP55 Series

Бренд: B+B SmartWorx Страницы: 120

Бренд: VERTO Страницы: 48

Vigor 3200 Series

Бренд: Draytek Страницы: 356

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды