rtd cpuModule CME37786HX Скачать руководство пользователя страница 20

Страница: 20 / 122

CME37786HX

RTD Embedded Technologies, Inc.

Cable Kits

For maximum flexibility, cables are not provided with the cpuModule. You may wish to purchase
our cable kit for the cpuModule.

The XK-CM45 cable kit contains the following:

•

Utility Cable (keyboard, battery, reset, speaker)

•

2 Serial Port Cables (10 Pin DIL to DB-9)

•

Parallel Port Cable (26-pin DIL to DB-25)

•

PS/2 Mouse Cable (4-pin DIL to 6-pin mini-DIN)

•

VGA Cable (10-pin DIL to 15-pin D-sub)

•

IDE Cable (for 3.5" Hard Drive)

•

IDE Cable (for 2.5" Hard Drive)

•

10/100 base T and TX (10 Pin DIL TO RJ-45)

•

Audio Adapter (10 Pin DIL to 3 mini-jack connectors)

•

Power cable (DIL12 to wire leads)

•

Dual USB cable

Содержание cpuModule CME37786HX



























































































































Результаты поиска

Содержание cpuModule CME37786HX

Отзывы:

Похожие инструкции для cpuModule CME37786HX

Бренды по названию

Популярные бренды

rtd cpuModule CME37786HX, Руководство пользователя

Результаты поиска

Содержание cpuModule CME37786HX

Отзывы:

Похожие инструкции для cpuModule CME37786HX

Бренды по названию

Популярные бренды