background image

CME37786HX

RTD Embedded Technologies, Inc.

64

SSD/Failsafe 
Window

+, -, 
<PgUp>, 
<PgDn>

Sets the memory window to be used for the SSD de-
vice

• C000:0000
• C400:0000
• C800:0000
• CC00:0000
• D000:0000
• D400:0000
• D800:0000
• DC00:0000

OnBoard Lega-
cy Audio

+, -, 
<PgUp>, 
<PgDn>

Allows the integrated sound controller to emulate a 
Legacy ISA sound card (Sound Blaster, MPU-401).


• Enable
• Disable

Sound Blaster

+, -, 
<PgUp>, 
<PgDn>

Enables emulation of a Sound Blaster sound card.

• Enable
• Disable

SB I/O Base Ad-
dress

+, -, 
<PgUp>, 
<PgDn>

Selects the base address used for Sound Blaster em-
ulation.

• 220H
• 240H
• 260H
• 280H

SB IRQ Select

+, -, 
<PgUp>, 
<PgDn>

Selects the IRQ used for Sound Blaster emulation.

• IRQ  5 
• IRQ  7 
• IRQ  9 
• IRQ  10

SB DMA Select

+, -, 
<PgUp>, 
<PgDn>

Selects the DMA channel used for Sound Blaster 
emulation.

• DMA  0
• DMA  1
• DMA  2
• DMA  3

MPU-401

+, -, 
<PgUp>, 
<PgDn>

Enables emulation of an MPU-401 MIDI Processor.

• Enable
• Disable

MPU-401 I/O 
Address

+, -, 
<PgUp>, 
<PgDn>

Selects the base address used for MPU-401 emula-
tion.

• 300-303H
• 310-313H
• 320-323H
• 330-333H

Table 33: Integrated Peripherals Setup Fields (Continued)

Содержание cpuModule CME37786HX



























































































































Отзывы: