rtd cpuModule CME37786HX Скачать руководство пользователя страница 110

Страница: 110 / 122

CME37786HX

RTD Embedded Technologies, Inc.

102

Figure 4: CME37786HX Jumper Locations - Top

Figure 5: CME37786HX Jumper Locations - Bottom

Table 42: Jumpers and Default Settings

JP1

2-pin jumper
Used to enable/disable 120 ohm termination resistor on first serial port for
RS-422/485 mode.
default: Open (no termination)

JP2

2-pin jumper
Used to enable/disable 120 ohm termination resistor on first serial port for
RS-422/485 mode.
default: Open (no termination)

JP4

3-pin jumper
Used to select power for an SSD socket.

• 1 to 2 is 5 Volts on board.
• 2 to 3 is 5 volts on board when power on and battery backup when power

off

default: Positions 1 and 2.

JP5

2-pin jumper
Used for setting to boot to Fail Safe Boot ROM and restoring factory BIOS
settings
default: Open

JP6

2-pin jumper
Factory use only; do not close.
default: Open

Table 43: Solder Jumpers and Default Settings

Three position solder jumper to select 3.3 or 5 volt signaling on the PCI bus.

• Pads 1-2 shorted is 5 Volt signaling
• Pads 2-3 shorted is 3.3 Volt signaling. Default Setting

Two position solder jumper to connect USB shield ground to frame ground.
Default is not connected.

Three position solder jumper to select the source of 3.3V on the PCI bus.

• 2-3 -- PC/104

Plus

PCI bus +3.3 volts supplied by on-board +3.3 volt reg-

ulator. Maximum current source is two (2) amps.

• 1-2 -- PC/104

Plus

PCI bus +3.3 volts supplied by power connector P9

pins 10 and 12. Default setting.

Two position solder jumper to connect frame ground to digital ground. De-
fault is not connected.

Two position solder jumper to connect Ethernet shield ground to frame
ground. Default is not connected.

Содержание cpuModule CME37786HX



























































































































Результаты поиска

Содержание cpuModule CME37786HX

Отзывы:

Похожие инструкции для cpuModule CME37786HX

Бренды по названию

Популярные бренды

rtd cpuModule CME37786HX, Руководство пользователя

Результаты поиска

Содержание cpuModule CME37786HX

Отзывы:

Похожие инструкции для cpuModule CME37786HX

Бренды по названию

Популярные бренды