rtd CMV6486DX100HR Скачать руководство пользователя

Страница: 83 / 118

• Save your changes and exit Setup.

• Turn off the cpuModule.

• Set jumpers JP1 and JP7 or JP2 and JP8 to appropriate settings.

Please see SSD Jumpers on page 102.

• Install the BIOS Extension Device into the correct socket.

• Reboot the cpuModule. The BIOS Extension Device should appear as the next avail-

able hard drive in your system. If there is no other hard drive installed, it will ap-
pear as drive C:.

• Format the new drive using the DOS format command.

• If you wish to boot from the BIOS Extension Device, run Setup and disable any other

hard drive. Set the boot device to Hard Drive. The cpuModule may not boot to a
BIOS Extension Device if another hard drive is enabled.

NOTE!

If you wish to make the drive bootable, you must format it using the /s
switch of the format command. Refer to your OS manual for more
information.

Содержание CMV6486DX100HR























































































































Результаты поиска

Содержание CMV6486DX100HR

Отзывы:

Похожие инструкции для CMV6486DX100HR

Бренды по названию

Популярные бренды

rtd CMV6486DX100HR, Руководство пользователя

Результаты поиска

Содержание CMV6486DX100HR

Отзывы:

Похожие инструкции для CMV6486DX100HR

Бренды по названию

Популярные бренды