rtd CMV6486DX100HR Скачать руководство пользователя страница 110

Страница: 110 / 118

110

Common Problems and Solutions

The following table lists some of the common problems you may encounter while using your cpu-
Module, and suggests possible solutions.

If you are having problems with your cpuModule, please review this table before contacting techni-
cal support.

Problem

Cause

Solution

cpuModule "will not boot"

no power or wrong polarity

check for correct power on PC/104 bus
connectors

incorrect Setup (video dis-
abled, etc.)

install jumper JP5; reboot and press {De-
lete} key to run Setup

defective or mis-connected de-
vice on bus

check for misaligned bus connectors;
remove other cards from stack

cable connected backwards

verify all cables are connected correctly

SSD installed backwards

check for an SSD memory installed in
socket backwards

entering Virtual Devices mode

check if first or second serial port is jum-
pered to force Virtual Devices mode

does not recognize Setup
changes

jumper JP5 installed

turn off power, remove JP5, reboot

Setup always runs at boot,
whether or not {Delete}
key is held

E000 segment mapped to
BIOS ROM

Enter Advanced Setup screen, change
E000 Segment Map to ’PC/104 Bus’

will not boot from particu-
lar drive or device

device not bootable

use sys command on drive or re-format the
device using the /s switch

Fail Safe Boot ROM enabled

Disable Fail Safe Boot ROM

device not formatted

format drive using /s switch

power not connected to boot
drive

connect power cable to floppy or hard
drive

"General Failure..." mes-
sage attempting to access
Atmel Flash in SSD

jumpers incorrectly set

set SSD jumpers correctly; see Jumper
Setting tables for SSD;
Note: if device was formatted with jump-
ers set incorrectly, it must be re-formatted

Added second Atmel Flash
to SSD; will not re-format
to larger size

format command must have
size specified

execute format command with /f:1.44
switch

Atmel Flash shows disk
space available, but it can-
not be written

part smaller than 1.44MB was
formatted as 1.44MB; it will
show space available even
when full

ignore "disk space remaining" messages
from DOS
REMEMBER! A bootable disk contains 3
hidden files plus format info, totalling
about 150kB

Содержание CMV6486DX100HR























































































































Результаты поиска

Содержание CMV6486DX100HR

Отзывы:

Бренды по названию

Популярные бренды

rtd CMV6486DX100HR, Руководство пользователя

Результаты поиска

Содержание CMV6486DX100HR

Отзывы:

Бренды по названию

Популярные бренды