rtd CMV6486DX100HR страница 100 Скачать руководство пользователя | Manualshive

Страница: 100 / 118

background image

100

Jumpers

The figure below shows the locations of the jumpers used to configure the cpuModule. To use the
figure, position the module with the PC/104 bus connector at the six o'clock position and the com-
ponent side facing up. The table below lists the jumpers and their settings.

Jumper

Use

JP 1

6-pin jumper.
Used with JP7 to configure first SSD socket.

Factory Default: (position 1-2)

JP 2

6-pin jumper
Used with JP8 to configure second SSD socket.

Factory Default: (position 1-2)

JP 3

2-pin jumper
Used to enable/disable 120 ohm termination resistor on first serial port.

Factory Default: Open (no termination)

JP 4

2-pin jumper
Used to enable/disable 120 ohm termination resistor on second serial port.

Factory Default: Open (no termination)

«
...
98
99
100
101
102
...
»

Содержание CMV6486DX100HR























































































































Отзывы:

Нет отзывов

Похожие инструкции для CMV6486DX100HR

AllShare Cast Dongle

Бренд: Samsung Страницы: 2

Бренд: D-Link Страницы: 14

Бренд: Datasat Страницы: 32

Бренд: Raritan Страницы: 4

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

Бренд: Accusys Страницы: 34

Бренд: Neo Instruments Страницы: 2

Бренд: peplink Страницы: 2

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: Hama Страницы: 6

PBE-5AC-300-ISO

Бренд: Ubiquiti Страницы: 28

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: Advantech Страницы: 66

Бренд: ZyXEL Communications Страницы: 2

airPoint Nexus sB3210

Бренд: SmartBridges Страницы: 55

Бренд: Aerotech Страницы: 62

Бренд: Quantum Страницы: 140

Бренд: IBASE Technology Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды