rtd CMV6486DX100HR Скачать руководство пользователя | Manualshive

Страница: 68 / 118

background image

68

Errors While Booting

If an error occurs while the system is booting and performing the Power On Self Tests, the system
will respond in one of several ways. Its response depends on what type of error occurred and on cer-
tain selections made in Setup.

Any error encountered in POST 1 through 7 causes the module to halt.

Errors encountered after POST 7 are dealt with according to settings made in Setup:

•

With an error set to OFF in the Setup, a message is displayed on the screen and the

speaker beeps. The boot continues if possible.

•

With an error set to ON in the Setup, a message is displayed on the screen (if possible)

and you are asked for confirmation before the boot continues.

If an error is detected in the EEPROM test (POST code 8) the system sets itself according to the de-
fault configuration presented in the following section. In that case, the system displays the detected
errors and waits for confirmation before the boot continues.

When an error occurs and you are asked for confirmation to continue the boot, the {F1} key must be
pressed to continue.

«
...
66
67
68
69
70
...
»

Содержание CMV6486DX100HR























































































































Отзывы:

Нет отзывов

Похожие инструкции для CMV6486DX100HR

PCMCIA WIRELESS ASAPTER DWL-650

Бренд: D-Link Страницы: 5

PowerLine DHP-W611AV

Бренд: D-Link Страницы: 78

Бренд: TC Electronic Страницы: 174

Finalizer Express

Бренд: TC Electronic Страницы: 33

EK-FC1080 GTX Ti TF6

Бренд: ekwb Страницы: 2

Бренд: Commell Страницы: 9

SOUL CALIBUR II

Бренд: NAMCO Страницы: 26

EK-FC750 GTX Series

Бренд: ekwb Страницы: 2

Бренд: ZALMAN Страницы: 18

Бренд: Corsair Страницы: 12

XC-16CH-NVR-4TB

Бренд: Xyclop Страницы: 19

Бренд: Patton electronics Страницы: 8

Бренд: LevelOne Страницы: 49

Бренд: Keysight Technologies Страницы: 106

Бренд: M-system Страницы: 4

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

MTDOT-868 Series

Бренд: Multitech Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды