Royal Enfield CONSTELLATION 1958 Скачать руководство пользователя | Manualshive

Страница: 86 / 106

background image

Section J1 Page 3

removal  of  the  main  tube  bush  the  bottom  tube
bush,  oil  seal  housing  and  oil  seal  can  be
removed.In case of difficulty in removing the main
tube  bush  it  is  possible  to  withdraw  the  oil  seal
housingafter  loosening  the crown  clip  bolt  39038,
removing  the  plug  screw  38968  and  unscrewing
the  main  tube  from  the  fork-head  by  means  of  a
hexagon bar .500 in. across flats (Unbrako wrench
W. 11) or the special tool shown in Fig. 2.

4. Spring

Solo and Sidecar springs are available. The free

length of each is 20.1/2 ins. The spring should be
replaced if it has closed by more than 1 inch.

5. Reassembly of Parts

When refitting the oil seal, or fitting a new one,

great  care  must  be  exercised  not  to  damage  the
synthetic rubber lip which forms the actual seal. If
the  seal  has  been  removed  from  the  upper  end  of
the  main  tube  and  is  refitted  from  this  end  a
special nose piece (Fig. 3) must be fitted over the
end  of  the  tube  to  prevent  the  thread  from
damaging the oil seal.

The spring stud is a tight fit in the hole at the

lower end of the bottom tube. Once the stud has
been entered in the hole push the bottom tube

SHOWING THE POSITIONS OF THE CLAMP BOLTS
SECURING THE STEERING STEM AND FORK TUBES

Fig. 4

up  sharply  against  the  spring  until  two  or  three
threads  on  the  stud  project  beneath  the  end  of
the bottom tube. Now fit the nut and washer and
pull the stud into position by tightening the nut.
If  necessary  fit  the  nut  first  without  the  washer
until sufficient thread is projecting to enable the
washer to be fitted.

6. Steering Head Races

The steering head bearing consists of two

deep  groove  thrust  races  each  containing
nineteen  1/4  in.  diameter  balls.  The  bearing  is
adjusted by tightening the steering stem locknut
after loosening the ball head clip screw and both
the fork crown clamp bolts. The head should be
adjusted  so  that,  when  the  front  wheel  is  lifted
clear of the ground, a light tap on the handlebars
will  cause  the  steering  to  swing  to  full  lock  in
either  direction,  while  at  the  same  time  there
should  be  only  the  slightest  trace  of  play  in  the
bearings.  When  testing  for  freedom  of
movement  the  steering  damper,  if  fitted,  should
be disconnected by unscrewing the anchor plate
pin.  Do  not  forget  to  tighten  the  ball  head  clip
screw  and  fork  crown  clamp  bolts.  Before
tightening  the  latter  make  sure  that  the  cover
tubes are located centrally round the main tubes
so  that  the  bottom  tube  does  not  rub  inside  the
cover  tube.  A  pair  of  split  bushes  (Fig.  5)  is
useful to ensure centralisation of the cover tubes.

7. Removal of Complete Fork

The fork complete with front wheel and

mudguard can be removed from the machine if
necessary by adopting the following procedure.

www.hitchcocksmotorcycles.com

«
...
84
85
86
87
88
...
»

Содержание CONSTELLATION 1958











































































































Отзывы:

Нет отзывов

Похожие инструкции для CONSTELLATION 1958

Бренд: Kabuto Страницы: 12

Бренд: hepco & becker Страницы: 4

Бренд: GAS GAS Страницы: 74

Бренд: KTM Power Parts Страницы: 7

Бренд: Honda Страницы: 150

Бренд: Androware Страницы: 2

Бренд: Silvercrest Страницы: 42

Бренд: tucanourbano Страницы: 4

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER H0PC10ST

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

Бренд: Honda Страницы: 384

Bullet 350 2019

Бренд: Royal Enfield Страницы: 68

Бренд: Honda Страницы: 415

Бренд: 3M Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды