Royal Enfield CONSTELLATION 1958 Скачать руководство пользователя | Manualshive

Страница: 84 / 106

background image

SECTION J1

Front Fork

With Casquette and Aluminium Alloy Bottom Tubes

1. Description

The telescopic fork consists of two legs each

of  which  comprises  a  main  tube  of  chrome
molybdenum  alloy  steel  tubing  which  is
screwed  into  the  Casquette  fork  head  at  the
upper  end  and  securely  clamped  to  the  fork
crown.  Fitted  over  the  lower  end  of  the  main
tube  is  the  bottom  tube  made  of  high  strength
aluminium  alloy  with  an  integral  lug  which
carries  the  wheel  spindle.  Fitted  on  the  lower
end  of the  main  tube  is a steel  bush  which  is a
close  fit  in  the  bore  of  the  bottom  tube.  The
upper  end  of  the  bottom  tube  carries  a  bronze
bush  which  is  a  close  fit  over  the  outside
diameter  of the  main  tube.  The  bush is  secured
to  the  bottom  tube  by  means  of  a  threaded
housing  which  contains  an  oil  seal.  A  stud
known as the "spring stud" is fitted in the lower
end  of  the  bottom  tube  and  a  valve  port  is
secured  to  the  lower  end  of  the  main  tube.  As
the  fork  operates  oil  is  forced  between  the
spring  stud  and  the  bore  of  the  valve  port
forming  a  hydraulic  damping  system.  A
compression spring is fitted inside the main tube
between the upper end of the spring stud and the
upper  end  of  the  main  tube.  The  lower  end  of
the main tube and upper end of the bottom tube
are  protected  by  a  cover  secured  to  the  fork
crown.

A special fork is available for sidecar

machines. This has bottom tubes with extended
wheel lugs giving less trail and is fitted with
stronger springs and a steering damper.

2. Operation of the Fork

The fork provides a range of movement of 6

in. from the fully extended to the fully
compressed

position.

The

movement

is

controlled by the compression spring and by the
hydraulic  damping  system.  The  hydraulic
damping is light on the bump stroke and heavier
on  the  rebound  stroke,  thus  damping  out  any
tendency  to  pitching  or  oscillation  without
interfering  unduly  with  the  free  movement  of
the fork when the wheel encounters an obstacle.

The fork is filled with S.A.E. 20 to a point

above the lower end of the fork spring so that
the damper chamber "B" is always kept

Section J1 Page 1

www.hitchcocksmotorcycles.com

«
...
82
83
84
85
86
...
»

Содержание CONSTELLATION 1958











































































































Отзывы:

Нет отзывов

Похожие инструкции для CONSTELLATION 1958

Бренд: Cannondale Страницы: 102

Бренд: KAYO MOTOR Страницы: 74

Бренд: KAYO MOTO Страницы: 5

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: ACERBIS Страницы: 72

Бренд: yasuni Страницы: 8

Бренд: hepco & becker Страницы: 2

Бренд: Honda Страницы: 123

Бренд: Yamaha Страницы: 109

Бренд: Yamaha Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды