Royal Enfield CONSTELLATION 1958 Скачать руководство пользователя | Manualshive

Страница: 96 / 106

background image

17. Tyre

The standard tyre is Dunlop 3.50-19 in.

studded tread.

When removing the tyre always start close to

the valve and see that the edge of the cover at
the other side of the wheel is pushed down into
the well in the rim.

When replacing the tyre fit the part by the

valve last, also with the edge of the cover at the
other side of the wheel pushed down into the
well.

If the correct method of fitting and removal

of  the  tyre  is  adopted  it  will  be  found  that  the
covers  can  be  manipulated  quite  easily  with  the
small  levers  supplied  in  the  tool-kit.  The  use  of
long  levers  and/or  excessive  force  is  liable  to
damage  the  walls  of  the  tyre.  After  inflation
make  sure  that  the  tyre  is  fitting  evenly  all  the
way  round  the  rim.  A  line  moulded  on  the  wall
of  the  tyre  indicates  whether  or  not  the  tyre  is
correctly fitted. If the tyre has a white mark

indicating a balance point, this should be fitted
near the valve.

18. Tyre Pressures

The recommended pressures for the rear tyre

are 20 lb. per sq. in. for a solo rider and 32 lb.
per sq. in when a pillion passenger is carried.

19.

Lubrication

Grease the bearings by packing them with

grease after dismantling the hub as described
above.

Note that the brake cam is drilled for a grease

passage but the end of this is stopped up with a
countersunk screw instead of being fitted with a
grease nipple. This is  done  to  prevent excessive
greasing by over-enthusiastic owners. If the cam
is  smeared  with  grease  on  assembly  it  should
require  no  further  attention  but  in  case  of
necessity it is possible to remove the screw, fit a
grease nipple in its place and grease the cam by
this means.

Section L9 Page 5

www.hitchcocksmotorcycles.com

«
...
94
95
96
97
98
...
»

Содержание CONSTELLATION 1958











































































































Отзывы:

Нет отзывов

Похожие инструкции для CONSTELLATION 1958

Бренд: N-Com Страницы: 28

Бренд: DAELIM Страницы: 2

Бренд: Takegawa Страницы: 2

fire PANTLINER AJ6

Бренд: ALPENHEAT Страницы: 26

Бренд: Artotic Страницы: 9

Бренд: DYNATEK Страницы: 12

Бренд: Yamaha Страницы: 81

2011 Star XV250A

Бренд: Yamaha Страницы: 90

2011 V Star XVS650A

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 96

2010 V Star XVS650AZ

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 88

2009 V Star XVS250X

Бренд: Yamaha Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды