Royal Enfield CONSTELLATION 1958 Скачать руководство пользователя | Manualshive

Страница: 32 / 106

background image

8. Removal of the Dual Seat and Rear
Mudguard

Disconnect the leads to the rear lamp by

pulling out the plugs in the connectors near the
tool box.

Loosen the two nuts on either side of the seat

attaching the mudguard carrier to the frame and
lift the seat, mudguard and carrier off together.

9. Removal of the Petrol Tank

Remove the petrol tank by detaching the

petrol  pipe  and  removing  the  rubber  mounted
stud  which  secures  the  front  of  the  tank  to  the
frame.  With  early  models  release  the  bottom
section of the rear clip by unscrewing the two 1/4
in.  attachment  nuts.  Tap  out  the  two  studs  and
raise the rear of the tank to release the clip. The
tank may then be removed.

With later models the rear tank attachment is

in the form of a laterally situated bracket with a
rubber  block  fixed  to  it,  this  bears  against  the
underside  of  the  frame  top  tube,  drawing  the
tank  down  on  to  the  rubber  covering  of  the  top
tube.

To remove, unscrew the two bolts securing

the bracket and lift the tank clear.

10. Removal of the Cylinder Head

First remove the petrol tank and petrol pipe.

(Subsection 9.)

The dual seat may also be removed if

desired. (Subsection 8.)

Disconnect the head steady link (early
models).
Remove head steady brackets (later models).

Disconnect the oil pipes and plug leads.

Remove the exhaust pipes and carburettor(s)

and induction manifold.

Remove the rocker box covers.
Turn the engine until both valves are closed.

Remove the five cylinder head nuts from

each head and lift off.

In replacing the heads, see that the dowels are

in position in the cylinder barrels and that the
push rods are the right way up (shallow cups
upwards).

Apply a thin coat of jointing compound to

both sides of the gasket and place it in position.

Lower the cylinder heads over the push rods,

making sure that the rockers locate in the push
rod cups.

Fit the head nuts and washers and partially

tighten down.

When both heads have reached this stage, fit

the  induction  pipe  and  tighten  the  nuts.  The
cylinder head nuts can now be finally tightened
down  progressively  and  diagonally  from  one
side to the other to prevent distortion. After the
engine  has  been  run  long  enough  to  get
thoroughly  hot,  the  tightness  of  the  nuts  should
be rechecked.

11.

Removal of the Valves

Having removed the cylinder head, remove

the rockerbox covers, each held by four nuts,
and swing the rocker clear of the valve. Using a
suitable

valve

spring

compressing

tool,

compress the valve springs and remove the split
collets from the end of the valve stem. Slacken

back the compressing tool and release the

Section C11 Page 3

www.hitchcocksmotorcycles.com

«
...
30
31
32
33
34
...
»

Содержание CONSTELLATION 1958











































































































Отзывы:

Нет отзывов

Похожие инструкции для CONSTELLATION 1958

Бренд: Honda Страницы: 104

Бренд: FDC Страницы: 6

Бренд: Victory Motorcycles Страницы: 332

Бренд: Honda Страницы: 130

Бренд: Zero Страницы: 290

RMAX WOLVERINE 2021

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 396

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 198

Бренд: Yamaha Страницы: 274

Бренд: Yamaha Страницы: 356

Бренд: Yamaha Страницы: 376

Бренд: Yamaha Страницы: 564

Бренд: Yamaha Страницы: 392

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 674

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды