manualshive.com logo in svg

Rotec AEROSPORT R2800, Руководство по эксплуатации, Страница: 83 / 87

Поделиться
Скачать
Rotec AEROSPORT R2800 Скачать руководство пользователя страница 83

ROTEC AEROSPORT | 83

www.RotecAerosport.com

LOWER CYLINDER OIL LEAKS

Oil and radials come hand in hand. After shut down oil must drain to the lower cylinders. Oil will weep past the piston 

rings and if an exhaust valve is open it will end up on the floor. If an inlet valve is open, it will fill the intake pipes. That is 

why intake drains on the lower cylinders must be open at all times when the engine is shut down to prevent hydraulic 

lock.

After shutdown, we recommend you attached containers on the exhaust pipes to catch oil as it drains. You can catch 

oil from the intake drains by connecting 1/2’’ hose. Drained oil is always reused by using a strainer and funnel to recy-

cle it back into the oil tank. The Rotec Radial can fill the containers by up to 2 liters after shutdown, making recycling 

important.

Oil can also siphon from a high mounted oil tank. To stop this use an anti-drain back oil filter or oil shut off tap be

-

tween the oil tank and inlet of the oil pump.

The electric oil scavenger pump helps to minimize oil loss as it pulls all unwanted oil out of the engine after shutdown.

Aside from the exhaust and intake drains, oil should not leak from other areas.

Содержание AEROSPORT R2800
























































































Отзывы:

Нет отзывов