manualshive.com logo in svg

Rotec AEROSPORT R2800, Руководство по эксплуатации, Страница: 32 / 87

Поделиться
Скачать
Rotec AEROSPORT R2800 Скачать руководство пользователя страница 32

32 | ROTEC AEROSPORT

www.RotecAerosport.com

ENGINE 

INSTALLATION

R2800 LOWER PIN MOUNTS

See also the lower engine mount assembly (all supplied) the hollow weldable pin is welded to the lower portion of 

the engine frame, the same rubber cushions as used on the top mount are also used . The entire assembly is retained 

via the machined alloy washer, through bolt and M8 nylock nut. Note that when tightening, the assembly will crush 

the rubber cushions to the correct amount once the metal componenents have “bottomed out” out at a length set by 

design. Further tightening beyond this point will not increase the crush on the rubber cushions.

R2800 COMPONENTS:

Code:

Name:

Qty:

R.164.1

Male Rubber Bushes

4

R.164.2

Female Rubber Bushes

4

R.070

Pin

2

R.069

Flared Sleeve

2

R.068

Cup

2

R.063.1

Step Washer

2

R.063.2

Flat Washer

2

NM10N

Nyloc Nut M10

2

NM8N

Nyloc Nut M8

2

SHCSM8120 SHCS M8 x 120

2

R.164.2

R.063.1

SHCSM8120

R.070

R.164.1

NM8N

Figure 15. Exploded Engine Mount Pin Side View

Figure 16. Engine Mount Pin Detail View

Figure 17. Exploded Engine Mount Pin Side View

Содержание AEROSPORT R2800
























































































Отзывы:

Нет отзывов