manualshive.com logo in svg

Rotec AEROSPORT R2800, Руководство по эксплуатации, Страница: 36 / 87

Поделиться
Скачать
Rotec AEROSPORT R2800 Скачать руководство пользователя страница 36

36 | ROTEC AEROSPORT

www.RotecAerosport.com

PROPELLER

RECOMMENDED SPECIFICATIONS

Viewed from the front of the engine, the Rotec Radial prop-shaft rotates counter clockwise (CCW). Therefore, a stan-

dard orientation propeller is used. This is reversed when the engine is used in pusher configuration.

Engine

Rotec R2800

Rotec R3600

Blades

2

2*

Diameter*

1.93m (76’’)

2.13m (84’’)

Pitch*

1.40m (55’’)

1.40m (55’’)

NOTE:

When selecting a propeller with lesser diameter than recommended, an increase in pitch is necessary. For example, a 

Rotec R3600 with propeller of 78’’ - 80’’ diameter will need a pitch of 56’’.

NOTE:

When selecting a propeller with a pitch greater than recommended, a reduction in propeller diameter is necessary. 

For example, a Rotec R2800 with a 76’’ diameter propeller, with a pitch of less than 53’’, will see the engine over 

speed at WOT.

NOTE:

A three blade, wood laminated, 68’’ diameter, 82’’ pitch propeller has been successfully used on a Zenith CH 200.

PERFORMANCE BY POWER SETTING

MOUNTING BOLTS

Rotec Radial Power Setting

Target Engine RPM*

Target Propeller RPM

100% (Static)

3000 - 3100

2000 - 2067

100% (Take Off)

3250 - 3350

2167 - 2233

75% (Crusie)

3000 - 3250

2000 - 2167

NOTE:

Using a recommended propeller, will see the engine work in its target performance range. Engines should not ex-

ceed approximately 3500 RPM with a propeller mounted, as going any higher will only result in the blades ‘slapping’ 

the air (2333 propeller RPM)

To avoid confusion and waste, propeller bolts are not supplied with new engines. There is no standard propeller thick-

ness and therefore no standard propeller bolt length.

Propeller Bolts Required:

• 

R2800 - 6 x Metric M8 x 1.25

• 

R3600 - 6 x Imperial 3/8-24 UNF

Propeller bolt torque settings are to be recommended by the propeller manufacturer. Torque specifications are depen

-

dent on the propeller material and thickness. For more information on propellers bolt torque specifications, contact 

the manufacturer.

Corrosion Resistance:

• 

Propeller drive dowels (lugs) - case hardened

• 

Propeller hub - electroless nickle plated

Содержание AEROSPORT R2800
























































































Отзывы:

Нет отзывов