Ross TES9 Скачать руководство пользователя страница 19

Страница: 19 / 68

TES9 Software User Manual (Iss. 04)

Encoder Configuration • 3–3

Configuring the Encoder for Setup Mode

Whenever the TES9’s power is turned on, it begins operation using parameters stored in its
configuration memory. In order to change these operating parameters via

Port A

or the modem,

the TES9 must be placed in setup mode. All data sources should stop sending data to the encoder
before running TES9Set.

To select Setup mode

Ensure that the TES9 has completed its power-up sequence and is operational.

Press and hold the

LOAD

switch located on the TES9's rear panel for at least two

seconds. Refer to the

TES9 Hardware Manual

for switch location.

When the

STATUS 1

LED begins alternating between green and yellow, the TES9 is

ready to be configured, and waiting for TES9Set to communicate with it using one of its
ports (

Port A

, modem or LAN).

The TES9 will leave Setup mode when you exit from TES9Set or you turn the TES9's
power off and on again.

To use setup via the LAN

You need to initially set the encoder's IP address through

Port A

or the modem, using

the above procedure.

After this initial setup, the TES9's configuration can be changed via the LAN connection
at any time, without pressing the

LOAD

switch to select

Setup

mode.

Содержание TES9





































































Результаты поиска

Содержание TES9

Отзывы:

Бренды по названию

Популярные бренды

Ross TES9, Руководство пользователя программного обеспечения

Результаты поиска

Содержание TES9

Отзывы:

Бренды по названию

Популярные бренды