manualshive.com logo in svg

Ross TES9, Руководство пользователя программного обеспечения

Поделиться
Скачать
Ross TES9 Скачать руководство пользователя страница 11

TES9 Software User Manual (Iss. 04)

Introduction • 1–3

Figure 1.2  

Workflow Diagram — Simple Data Distribution System

Video Source

The video source provides the serial digital video signal into which the TES9 encoder inserts the 
VANC data. The video signal may be any of those listed in 

Table 1.1

. 

Transmit Computer

The transmit computer executes application programs that

• configure the encoder; and/or
• supply data to the encoder

TES9Set, the application program used to configure the TES9, is supplied with the TES9. This is 
for use on computers with Microsoft® Windows 98® operating system or later.

Data is sent to the encoder by application programs which may be written specifically for the data 
distribution system (e.g. a closed captioning server), or may be a generalized source of a serial 
data stream.

Table 1.1  Supported Video Formats

Type

Format

Defining Standards

259M

525 lines, 59.94 Hz

ITU-R BT.601, SMPTE 125M

625 lines, 50 Hz

ITU-R BT.601

292M

1080i, 50 Hz

SMPTE 274M

1080i, 59.94 Hz

SMPTE 274M

1080i, 60 Hz

SMPTE 274M

1080p, 23.98 Hz

SMPTE 274M

1080p, 24 Hz

SMPTE 274M

1080sf, 23.98 Hz

SMPTE 274M, RP211

1080sf, 24 Hz

SMPTE 274M, RP211

720p, 50 Hz

SMPTE 296M

720p, 59.94 Hz

SMPTE 296M

720p, 60 Hz

SMPTE 296M

VIDEO

SOURCE

TRANSMIT

COMPUTER

RECEIVE

COMPUTER

TES9

ENCODER

TES9

RECEIVER

Broadcast

Network

Video

Legend

RS-232, LAN, or MODEM

RS-232, or LAN

Содержание TES9





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды