RosRoca Olympus Mini Скачать руководство пользователя страница 37

Страница: 37 / 110

49. Press and hold the ‘Tailgate raise’ switch until the

tailgate is fully raised and then release the switch.

4647-OM1-R-GB-G1

No errors

Hyd Oil Temp

No errors

01.06.2013 09:00:00

Hyd_Oil_Pressure

210 Bar

• Tailgate should raise until fully raised when it

should stop without noticeable judder.

• ‘Vehicle reversing’ alarm should sound while

tailgate is rising.

• ‘Tailgate raised’ pictogram should display on

the control panel screen.

• Immediately the tailgate reaches full height, the

compaction mechanism should not operate.

50. Press and hold the ‘Lower tailgate to 1 metre’

switch until the tailgate stops lowering and then
release the switch.

4700-OM1-R-GB-G1

No errors

Hyd Oil Temp

No errors

01.06.2013 09:00:00

Hyd_Oil_Pressure

10 Bar

• Tailgate should rotate smoothly downwards

about the hinge pins until it is 1 metre from the

body when it should stop without noticeable
judder.

• ‘Vehicle reversing’ alarm should sound while

tailgate is lowering.

• ‘Tailgate out‑of‑locks’ pictogram, A, should

display on the control panel screen.

dAILY CHeCKS

3‑13

OM1R-SM-GB01R

Содержание Olympus Mini















































































































Результаты поиска

Содержание Olympus Mini

Отзывы:

Бренды по названию

Популярные бренды

RosRoca Olympus Mini, Руководство по обслуживанию

Результаты поиска

Содержание Olympus Mini

Отзывы:

Бренды по названию

Популярные бренды