RosRoca Olympus Mini Скачать руководство пользователя страница 32

Страница: 32 / 110

34. On each compaction mechanism control panel,

press in turn the:

4552-OM1-R-GB-G1

‘Start pack cycle’ push‑

button.

4550-OM1-R-GB-G1

‘Rescue’ push‑button.

• Compaction mechanism should not operate.

wARNING:
MAKe SuRe THAT YOu KNOw THe HeIGHT

OF YOuR VeHICLe wITH THe TAILGATe
ANd wASTe CONTAINeR LIFTING deVICe,
IF FITTed, RAISed.

35. Press and hold the ‘Tailgate raise’ switch.

4645-OM1-R-GB-G1

No errors

Keine Fehler

Hyd Öl Temp Grad C

Keine Fehler

01.06.2013 09:00:00

Hyd Öl Druck bar

210 Bar

• Tailgate should rotate smoothly upwards about

the hinge pins.

• ‘Vehicle reversing’ alarm should sound.

36. While tailgate is rising, release the switch before it

reaches its fully raised position.

• Tailgate should stop rising immediately the

switch is released.

• Tailgate should not lower.

• ‘Tailgate out‑of‑locks’ pictogram should display

on the control panel screen.

2748-DS049-OL1-D-GB-G2

No errors

Hyd Oil Temp

No errors

01.06.2013 09:00:00

Hyd_Oil_Pressure

210 Bar

• ‘Vehicle reversing’ alarm should silence.

dAILY CHeCKS

3‑8

OM1R-SM-GB01R

Содержание Olympus Mini















































































































Результаты поиска

Содержание Olympus Mini

Отзывы:

Бренды по названию

Популярные бренды

RosRoca Olympus Mini, Руководство по обслуживанию

Результаты поиска

Содержание Olympus Mini

Отзывы:

Бренды по названию

Популярные бренды