Rosemount 8732C Скачать руководство пользователя страница 82

Страница: 82 / 126

Rosemount Model 8732C Integral Mount Magnetic Flowmeter System

7-2

TABLE 7-1. Relation
Between Ambient
Temperature, Process
Temperature, and
Temperature Class.

Submergence Protection

Continuous to 30 feet (10 meters). IP 68.

Standard Hazardous Locations Certifications

Factory Mutual (FM) Approvals

Approved for Class I, Division 2, Groups A, B, C, and D; Class II, Division 1,
Groups E, F, and G; Class III hazardous locations.
NEMA 4X.

Canadian Standards (CSA) Approval

Approved for Class I, Division 2, Groups A, B, C, and D; Class II, Division 1,
Groups E, F, and G; Class III hazardous locations,
CSA enclosure 4.

Optional Hazardous Locations Certifications

KEMA/CENELEC
KD

EEx e ia IIC T3...T6. See Table 7-1.

Conductivity Limits

Process liquid must have a conductivity of 5 microsiemens/cm (5 micromhos/cm)
or greater. Excludes the effect of interconnecting cable length in remote mount
transmitter installations.

Pressure Limits

See Table 7-2

Meter Size

(inches)

Maximum Ambient

Temperature

Maximum Process

Temperature

Temperature Class

149 °F (65 °C)

240 °F (116 °C)

1
1

149 °F (65 °C)

95 °F (35 °C)

248 °F (120 °C)

95 °F (35 °C)

T3
T4

1½
1½

149 °F (65 °C)
140 °F (60 °C)

257 °F (125 °C)

140 °F (60 °C)

T3
T4

2
2
2

149 °F (65 °C)
149 °F (65 °C)
104 °F (40 °C)

257 °F (125 °C)

167 °F (75 °C)
104 °F (40 °C)

T3
T4
T5

3 to 4
3 to 4
3 to 4
3 to 4

149 °F (65 °C)
149 °F (65 °C)
131 °F (55 °C)
104 °F (40 °C)

266 °F (130 °C)

167 °F (75 °C)
194 °F (90 °C)
104 °F (40 °C)

T3
T4
T5
T6

6
6
6
6

149 °F (65 °C)
149 °F (65 °C)
149 °F (65 °C)
140 °F (60 °C)

175 °F (79 °C)
167 °F (75 °C)

230 °F (110 °C)

140 °F (60 °C)

T3
T4
T5
T6

8 to 60
8 to 60
8 to 60
8 to 60

149 °F (65 °C)
149 °F (65 °C)
149 °F (65 °C)
149 °F (65 °C)

284 °F (140 °C)

240 °F (116 °C)

176 °F (80 °C)
149 °F (65 °C)

T3
T4
T5
T6

Содержание 8732C































































































































Результаты поиска

Содержание 8732C

Отзывы:

Похожие инструкции для 8732C

Бренды по названию

Популярные бренды

Rosemount 8732C, Руководство пользователя

Результаты поиска

Содержание 8732C

Отзывы:

Похожие инструкции для 8732C

Бренды по названию

Популярные бренды