Rosemount 8732C Скачать руководство пользователя страница 31

Страница: 31 / 126

2-19

Installation

Install Conduit

Transmitter junction boxes have ports for ¾-inch NPT
conduit connections.

1. Connect the ¾-inch NPT conduit to the transmitter in accordance

with local or plant electrical codes.

2. Seal unused ports to prevent moisture or other contamination

from entering the junction box.

Do not overtighten metal plugs used to seal wiring compartment ports;
overtightening can damage the housing.

Power Connections

To connect power to the transmitter, complete the following steps:

1. Ensure that the power source and connecting cable meet the

requirements outlined in Transmitter Input Power on page 2-5.

2. Turn off the power source.

3. Open the power terminal cover.

4. Run the power cable through the conduit to the transmitter.

5. Loosen the terminal cable guard for the input power terminals

L1 and N or +dc and -dc.

6. Connect the power cable leads as follows:

For an ac-powered transmitter:

• Connect ac Ground to a grounding lug.

• Connect ac Neutral to terminal N.

• Connect ac Line to terminal L1.

For a dc-powered transmitter:

• Connect dc Ground to a grounding lug.

• C dc.

• Connect – dc.

The dc-powered transmitter has a different terminal block and different
electronics that are not compatible with an ac-powered transmitter.

FIGURE 2-24. Power Connections.

Input Power
90–250 V ac

or 15–30 V dc

4–20 mA

Outputs

Digital Outputs

Grounding

Lugs

732

-00

Содержание 8732C































































































































Результаты поиска

Содержание 8732C

Отзывы:

Бренды по названию

Популярные бренды

Rosemount 8732C, Руководство пользователя

Результаты поиска

Содержание 8732C

Отзывы:

Бренды по названию

Популярные бренды