Rosemount 8732C Скачать руководство пользователя страница 79

Страница: 79 / 126

6-5

Model 8732C Specifications and Reference Data

NOTE

When removing or replacing the transmitter housing, refer to
Transmitter Removal Procedure on page 5-5.

MODEL 8732C SPARE PARTS

Part Description

Item

Number

Part Number

Model 8732C Electronics, 90–250 V ac (includes mounting hardware)

08732-0001-0001

Model 8732C Electronics with Non-volatile Totalizer, 90–250 V ac (includes mounting hardware)

08732-0001-0003

Model 8732C Electronics, 15-30V dc (Includes mounting hardware)

08732-0001-0002

Model 8732C Electronics with non-volatile totalizer, 15-30V dc (Includes mounting hardware)

08732-0001-0004

Standard Terminal Block Assembly (includes mounting hardware)

08732-0002-0001

Transient Protection Terminal Block Assembly (includes mounting hardware)

08732-0002-0002

DC Terminal Block Assembly (Includes mounting hardware)

08732-0002-0003

DC Transient Protection Terminal Block Assembly (Includes mounting hardware)

08732-0002-0004

Integral Mount Housing Assembly (does not include terminal block assembly)

08732-0004-0001

Standard Housing Cover (without glass for LOI)

08732-0005-0001

Local Operator Interface (LOI) Assembly (does not include LOI cover)

08732-0006-0002

LOI Cover

08732-0007-0002

Electrical Connection Assembly (Flowtube to transmitter)

08732-0133-0001

Model 8732C Non-Volatile Totalizer Chip

–

C53641-0003

Transmitter and Flowtube Accessories

Multi-Point Reference Calibration Standard (for use with Model 8712C, 8712U, or 8732C Transmitters)

—

Model 8714D

Spare Model 8714D Cable (for Model 8732C Transmitters)

—

08714-0205-0001

UMB Tube to 8732C Transmitter Conversion Bracket

—

08732-0160-0001

UMB Tube to 8732C Transmitter Conversion Cable (Three-position cable assembly)

—

08732-0161-0003

UMB Tube to 8732C Transmitter Conversion Cable (Four-position cable assembly)

—

08732-0161-0004

FIGURE 6-1. Model 8732C
Exploded Parts Drawing

FIGURE 6-1. Model 8732C Exploded Parts Drawing.

Three Board
Electronic Stack

(Items #1, 2, 3, or 4)

Terminal Block Assembly

(Item #5, 6, 7, or 8)

Electrical Connection
Assembly

(Item #13)

Housing Cover

(Item #10)

LOI Assembly

(Item #11)

LOI Cover

(Item #12)

Housing Assembly

(Item #9)

Содержание 8732C































































































































Результаты поиска

Содержание 8732C

Отзывы:

Похожие инструкции для 8732C

Бренды по названию

Популярные бренды

Rosemount 8732C, Руководство пользователя

Результаты поиска

Содержание 8732C

Отзывы:

Похожие инструкции для 8732C

Бренды по названию

Популярные бренды