manualshive.com logo in svg

Rosemount 8732C, Руководство пользователя

Rosemount 8732C - передовой датчик давления с возможностью подключения кальянного манометра. Используйте его вместе с нашим руководством для пользователя, которое можно скачать бесплатно с manualshive.com. Получите доступ к подробным инструкциям по использованию, чтобы максимально эффективно использовать этот продукт.

Поделиться
Скачать
background image

Rosemount Model 8732C Integral Mount Magnetic Flowmeter System

3-6

DIAGNOSTIC MESSAGES

The following error messages appear on the LOI screen when a diagnostic 
error is detected. To correct the problem, complete the steps as indicated. If 
the problem persists, contact your sales or service representative.

TABLE 3-2.  LOI Display and Functions.

LOI Display

Transmitter Function 

Display Setup

Display Lock ................... Locks out configuration changes (including totalizer start/stop/reset) from being made 

via the LOI. A DL indicator will show on the main flow rate screen. All values can still 
be viewed.

Flow Rate Display ........... User-selected settings for transmitter flow indication:

Flow-% Span, Flow-Totalize, %Span-Totalize.

Totalize Display ............... User-selected settings for transmitter totalizer indication:

Forward-Reverse, Net-Gross.

Basic Setup

Units: ................................... Specifies the desired units: Gal/Min, Lit/Min, IG/Min, CuM/Hr, Ft/Sec, M/Sec, Lit/sec, Special.
Tube Size ........................ Specifies the flowtube size (0.15 through 60 inches) and identifies the corresponding 

maximum flow.

Tube Cal No. ................... Identifies the flowtube calibration number.
URV, LRV........................ Sets the desired 20 mA (Upper Range Value) and 4 mA (Lower Range Value) points. 

Flowtube size must be set first.

Damping ......................... Sets response time, in seconds, to a step change in flow.

Detailed Set-up

Lo-Flow Cutoff................. Determines the flow rate at which the transmitter indicates an output of zero flow 

and 4 mA.

Dig Out Config ................ Selects pulse or auxiliary outputs, set pulse scaling and width, and select an auxiliary 

output (zero or reverse flow).

Special Units ................... Specifies input base unit, conversion, and time base for special units.
Coil Frequency................ Specifies coil drive frequency of 6 or 30 Hz.
Sig Processing ................ Specifies signal processing status (on/off) and sets signal processing parameters.

Transmitter Test

XMTR Test ...................... Performs a test of the transmitter electronics.
Loop Test ........................ Drives the transmitter analog output to a user-specified value.
Pulse Test ....................... Drives the transmitter digital output to a user-specified value.

Transmitter Trim

4–20 mA Trim ................. Adjusts the 4–20 mA Output.
Auto Zero ........................ Performs flowtube zero for 30 Hz operation.
Gain Trim ........................ Performs a calibration of the transmitter.

Device Information

Permits viewing and changing useful information about the transmitter and flowtube.

TABLE 3-3.  LOI Error Messages.

Symptom

Potential Cause

Corrective Action 

“Empty Pipe” displayed

Empty pipe.

None. Message will clear when pipe is full.

Electrode failure.

Perform flowtube tests C and D on page 5-5. 

Conductivity less than 5 

m

mho per cm.

Increase conductivity to 

≥ 

5 

m

mho per cm.

“Coil Open Ckt” displayed.

Damaged coils.

Check flowtube coils. Perform flowtube 
Test A–Flowtube Coil on page 5-5.

Electronics failure.

Replace Model 8732C electronics.

Flowtube will not Autozero
(“Autozero Failure” can be cleared by cycling power).

Flow is not set to zero.

Force flow to zero, re-perform autozero.

LOI is blank.

Model 8732C is ranged improperly. 

Correct ranging with HART-based Communicator.

LOI failure.

Replace LOI.

Electronics failure.

Replace electronics. 

LOI blinks, scrolls, or displays scrambled letters.

Unit experienced large transient.

Recycle power. If problem persists replace  electronics.

LOI does not respond to key press.

LOI failure.

Replace LOI. Use the HART Communicator 
in the interim.

Electronics failure.

Replace the electronics. 

LOI Glass is dirty.

Clean the LOI glass.

Содержание 8732C































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8732C

Panasonic LP-400 Series External Control Manual preview
LP-400 Series
Бренд: Panasonic Страницы: 180
ABQ Industrial TI-25MX Instruction Manual preview
TI-25MX
Бренд: ABQ Industrial Страницы: 15
ABQINDUSTRIAL HT-4000 User Manual preview
HT-4000
Бренд: ABQINDUSTRIAL Страницы: 3
E Instruments E500 Quick Manual preview
E500
Бренд: E Instruments Страницы: 2
Hach TitraLab User Manual preview
TitraLab
Бренд: Hach Страницы: 38
Hach sension ph31 Manual preview
sension ph31
Бренд: Hach Страницы: 28
Hach FH950 User Manual preview
FH950
Бренд: Hach Страницы: 40
Hach POCKET COLORIMETER II Basic User Manual preview
POCKET COLORIMETER II
Бренд: Hach Страницы: 142
Hach DR/2010 Instruction Sheet preview
DR/2010
Бренд: Hach Страницы: 4
Hach Lange 2100AN Basic User Manual preview
Lange 2100AN
Бренд: Hach Страницы: 308
Hach ANATEL PAT700 Operator'S Manual preview
ANATEL PAT700
Бренд: Hach Страницы: 158
Hach AMTAX sc User Manual preview
AMTAX sc
Бренд: Hach Страницы: 118
Hach POCKET COLORIMETER II Instruction Manuals preview
POCKET COLORIMETER II
Бренд: Hach Страницы: 116
Hach 5500sc Maintenance And Troubleshooting Manual preview
5500sc
Бренд: Hach Страницы: 132
Hach DR 6000 Instruction Manual preview
DR 6000
Бренд: Hach Страницы: 8
Hach HQ1110 User Manual preview
HQ1110
Бренд: Hach Страницы: 38
Hach NA5600 sc Na+ Operation Manual preview
NA5600 sc Na+
Бренд: Hach Страницы: 200
Magnum Energy ME-BMK Quick Start Manual preview
ME-BMK
Бренд: Magnum Energy Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды