Roger PR311-BK Скачать руководство пользователя страница 26

Страница: 26 / 30

PR311-BK fv102 Rev B. ENG.doc.DOC

8/9/2006

_________________________________________________________________________________________

Page

One long signal
continuously
repeated

♫

… and so on

Memory contents corrupted or MASTER card not
programmed - memory reset necessary. This signal is
accompanied by the steady lit LED SYSTEM.

Legend:

♫

- one long audible signal

♪

- one short audible signal (beep).

Table 7. LED indication.

LED

STATUS

LED OPEN

LED

SYSTEM

Meanings

Steady

(green)

— —

Controller is

Disarmed

Steady

(red)

— —

Controller is

Armed

Steady

(green)

— Steady

Controller is in the

User Programming

mode.

Flashing

(green)

— Flashing

Controller is waiting for next step during the

User Programming

mode.

—

Flashing

Controller is waiting for an identifier.

— Steady —

The door lock is activated; this LED remains ON as long as the
door lock is energized.

— —

Steady

The memory contents corrupted or MASTER identifier not
programmed. This situation is accompanied by acoustic signal
repeated in sequence: sound 2s/pause 2s.

Blinking Blinking Steady

The controller is being programmed from PC, the LED STATUS and
OPEN are blinking along with data send/received by a device.

Appendix

Table 8. Connection cable assignments.

Wire Color

Label

Description

Red

+12V

Supply input plus.

Black

GND

Supply input minus.

Pink

IN1

Input line, internally pulled up to the supply plus through a 5,6K resistor.

Blue

IN2

Input line, internally pulled up to the supply plus through a 5,6K resistor.

White-Yellow

IN3

Input line, internally pulled up to the supply plus through a 5,6K resistor.

Red-Blue

COM

Grey-Pink

Relay output contacts, 1A/24V DC/AC rated:
COM – common

Содержание PR311-BK































Результаты поиска

Содержание PR311-BK

Отзывы:

Похожие инструкции для PR311-BK

Бренды по названию

Популярные бренды

Roger PR311-BK, Инструкция по установке и программированию

Результаты поиска

Содержание PR311-BK

Отзывы:

Похожие инструкции для PR311-BK

Бренды по названию

Популярные бренды