Roger PR311-BK Скачать руководство пользователя страница 20

Страница: 20 / 30

PR311-BK fv102 Rev B. ENG.doc.DOC

8/9/2006

_________________________________________________________________________________________

Page

Programming

The programming of a PR311-BK is divided into two separate parts:

•

User Programming

•

Installer Programming

The

Installer Programming

is intended to configure the unit for specific installation

environment and can be carried out from PC computer only.
The

User Programming

is mainly dedicated to maintain Cards and PIN’s but it is

also designed to provide some other user commands. The

User Programming

can

be carried out remotely from PC or locally by means of

Programming Cards

5.1.

Programming Cards

The

Programming Card

is an ordinary proximity card or tag which was assigned for

specific user function. Up to 32

Programming Cards

can be defined in PR311-BK,

each

Programming Card

may have assigned only one programming function but

many

Programming Cards

may be assigned to a single user programming function.

The

Programming Cards

are defined during the initial installer’s setup and can be

carried out from PC only.

Note: The use of

Programming Cards

is restricted to controller only, it is not

possible to use the

Programming Cards

from the external reader connected to the

controller.

5.2.

Memory Reset - Programming MASTER Identifier

The

Memory Reset

Procedure clears entire contents of the PR311-BK memory and

restores default factory settings. During this procedure the new MASTER identifier
and the new controller ID number (address) can be programmed.

The

Memory Reset

consists of the following steps:

•

Power down the unit

•

Remove all connections from CLK and DTA lines

•

Make connection between CLK to DTA lines

•

Restore power, the unit will generate a continuous beep

•

Wait until the LED OPEN (green) starts flashing

•

Disconnect CLK from DTA

•

Present any a proximity card or tag to a unit, it will be a new MASTER identifier

•

Once the previous step is completed controller will generate signal OK and then
will enter the

Armed

mode

If the

Memory Reset

is not accomplished successfully or the content of controller’s

memory is corrupted then after power up the unit will signal memory error (LED

Содержание PR311-BK































Результаты поиска

Содержание PR311-BK

Отзывы:

Похожие инструкции для PR311-BK

Бренды по названию

Популярные бренды

Roger PR311-BK, Инструкция по установке и программированию

Результаты поиска

Содержание PR311-BK

Отзывы:

Похожие инструкции для PR311-BK

Бренды по названию

Популярные бренды