EN
57
CONTACT
DESCRIPTION
20(COS2) 22(COM)
Auxiliary input for connecting either a sensing edge
COS2
or a gate open limit switch on
0)%*ƼK
1. A sensing edge
COS2
in addition to
COS1.
8LIWIRWMRKIHKIMWGSRƼKYVIHF]HIJEYPX[MXLXLIJSPPS[MRKWIXXMRKW
–
. The sensing edge COS2 (NC contact) is disabled.
2. If the sensing edge is not installed, jumper the terminals
20(COS2) - 22(COM)
or
set
the parameter
.
&,WIVMIWW[MRKKEXIEYXSQEXMSRW]WXIQW[MXLEVXMGYPEXIHEVQ
$
), gate open li
mit switch on LEAF 2. The gate open limit switch for LEAF 2 is disabled by default
.
21(COS1) 22(COM)
Input (NC or 8 kOhm) for connecting sensing edge
COS1
ƼK
8LIWIRWMRKIHKIMWGSRƼKYVIHF]HIJEYPX[MXLXLIJSPPS[MRKWIXXMRKW
–
. If the sensing edge COS1 (NC contact) is enabled, the gate always reverses.
If the sensing edge is not installed, jumper the terminals
21(COS1) - 22(COM)
or
set the
parameter
.
23(ST) 22(COM)
STOP command input (NC).
The current manoeuvre is arrested if the safety contact opens.
N.B.:
XLIGSRXVSPPIVMWWYTTPMIH[MXLXLMWGSRXEGXEPVIEH]NYQTIVIHF]63+)68)',230
3+=
24 (ANT) 25
%RXIRREGSRRIGXSVJSVWPSXMRVEHMSVIGIMZIVFSEVH
9WI6+MJERI\XIVREPERXIRREMWYWIHQE\MQYQVIGSQQIRHIHPIRKXLQ
N.B.
: do not make joints in cable.
27(ORO) 26(COM)
Auxiliary input for connecting either a timer clock contact
ORO
or a gate open limit switch
SR0)%*ƼK
1. Clock timer contact input (N.O.).
When the clock function is active, the gate opens and remains open.
At the end of the programmed time set with the external device (clock) the gate closes.
2.
&,WIVMIWW[MRKKEXIEYXSQEXMSRW]WXIQW[MXLEVXMGYPEXIHEVQ
$
), gate open
limit switch on LEAF 1. The gate open limit switch for LEAF 1 is disabled by default
.
28(AP) 32(COM)
Open control signal input (N.O.).
29(CH) 32(COM)
Close command input (N.O.).
30(PP) 32(COM)
Step by step mode command input (N.O.).
The function of the control is determined by parameter
$
.
31(PED) 32(COM)
Partial open control signal input (N.O.).
On double leaf gate automation systems, by default, the partial opening command opens
LEAF 1 completely.
With single leaf swing gate installations, by default, partial opening is 50% of total ope
ning.
RECEIVER CARD
'SRRIGXSVJSVTPYKMRVEHMSVIGIMZIVFSEVH
The control unit has two radio remote control functions by default:
–
46WXITQSHIGSQQERHQSHMƼEFPI[MXLTEVEQIXIV
–
46TEVXMEPSTIRMRKGSQQERHQSHMƼEFPI[MXLTEVEQIXIV
BATTERY CHARGER
B71/BC
In the event of a mains power loss, the control unit is powered by the batteries. When
battery power is used,
E$WW
MWWLS[RSRXLIHMWTPE]ERHXLIƽEWLMRKPMKLXƽEWLIWFVMIƽ]
at intervals until mains power is restored or until the battery voltage drops below the
minimum permissible limit. In this case,
EW/2
(Battery Low) is shown on the display and
the control unit accepts no commands.
If mains power is lost while the gate is moving, the gate stops and then automatically
resumes the interrupted manoeuvre after 2 seconds.
