EN
61
14
4VSGIHYVEPZIVMƼGEXMSRW-2*31SHI
TEST
x5 s
TEST
1 click
...
TO QUIT
THE INFO MODE
INFO mode may be used to view certain parameters measured by the
B70/2DC
controller.
Press and hold the TEST button for 5 seconds from the “View command signals and safety devices” mode with the
motor stationary. The control unit displays the following parameters and the corresponding measured values in
sequence:
Parameter
Function
&QW
&QW
(MWTPE]WXLITSWMXMSRSJ1383613836I\TVIWWIHMRVIZSPYXMSRWERHVIPEXMZIXSXSXEPPIRKXLEXXLIXMQI
of the test.
/ Q
/ Q
:MI[XSXEPPIRKXLSJ1383613836TVSKVEQQIHXVEZIPMRQSXSVVIZSPYXMSRW
U3
U3
:MI[1383613836WTIIHMRVIZSPYXMSRWTIVQMRYXIV41
$ 3
$ 3
:MI[GYVVIRXEFWSVTXMSRSJ1383613836MR%QTIVIWIK!%!%
-JXLI1383613836MWWXEXMSREV]XLIGYVVIRXEFWSVTXMSRZEPYIMW%GXMZEXIEGSQQERHJYRGXMSRXSXIWX
current absorption.
E86
System OK indicator. To check for overloading (e.g.: too many utilities connected to 24 V output) or if the mains
voltage is too low, compare the parameters read with values indicated as follows with the motor stationary:
mains voltage= 230 Vac (nominal), bUS=
.
QEMRWZSPXEKI!:EG F97!
.
mains voltage= 253 Vac (+10%), bUS=
.
& 3
& 3
(MWTPE]GYVVIRXI\TVIWWIHMR%QTIVIWYWIHXSGSQTIRWEXIJSVWXVEMRHIXIGXIHF]1383613836HYI
for example, to low external temperatures (e.g.: 0 = 0 A ... 4 = +3 A). At the beginning of a manoeuvre from the
completely open or completely closed position, if the control unit detects a strain higher than the value stored
in its memory during the travel acquisition cycle, the controller automatically increases the current delivered to
1383613836
$6&
$6&
Display current threshold, expressed in Amperes, at which the obstacle detection function (crush prevention)
SJ1383613836MWXVMKKIVIH8LMWZEPYIMWGEPGYPEXIHEYXSQEXMGEPP]F]XLIGSRXVSPPIVMRVIPEXMSRXSXLI
settings of parameters
,
and
.
For the motor to function correctly,
$ 3
must always be lower than the value
$6&
.
7,Q
7,Q
Indicates time taken by motor to detect an obstacle, as set with parameter
, in seconds.
)K!W!WQW)RWYVIXLEXXLIQERSIYZVIXMQIMWQSVIXLERW
D%V
D%6
1383613836WXEXYW3/MRHMGEXSV-RRSVQEPGSRHMXMSRWXLMWZEPYIMWPIWWXLER-JXLIZEPYII\GIIHW
2000, the controller disables the motor. A value exceeding 500 indicates that the characteristics of the connec
tion cable are inadequate for the installation or that the connection cable is too long or of inadequate cross
section, or may indicate an electrical fault of the brushless motor.
83
If the control unit is capable of identifying the position of the gate leaf when the test is conducted, the following
is shown on the display:
83BB
position known, normal operation.
83B
LEAF 1 position unknown, position recovery in progress.
83B
LEAF 2 position unknown, position recovery in progress.
83
positions of both leaves unknown, position recovery in progress.
2&
-RHMGEXIWXLIWXEXISJXLIEYXSQEXMSRW]WXIQSTIRGPSWIH
2&23
automation system opening (motor active).
2&&/
automation system closing (motor active).
2&2
automation system completely open (motor not actives).
2&&
automation system completely closed (motor not actives).
8)
8)8
B
mains voltage too low or overload.
8)
B
+
motors overcurrent.
•
-JSRP]SRIQSXSVMWGSRRIGXIHXSXLIGSRXVSPYRMXXLITEVEQIXIVWVIPEXMZIXSƈ13836ƉSRP]EVIHMWTPE]IH
• Use the
+
-
buttons to scroll through the parameters. When the last parameter in the sequence is reached, press
the
-
button to return through the previous parameters.
• In INFO mode, the automation system may be activated to test operation in real time.
• Press and hold the TEST button for a few seconds to exit INFO mode
