Smart and intelligent!
The ROCO Lokmaus®2 is an ecenomy-priced digital control system. It was de-
signed and developed for digital beginners as well as for the advanced enthusiasts. It is the second ge-
neration of the very successfull ROCO Lokmaus. The compatibility to the standards of NMRA-DCC
guarantees you to get a system that fits the world-standard for two rails digital command controls
(DCC).
The Lokmaus®2 offers to you two levels of operation. Functions that could cause problems if they are
used by children can be easily protected against unintentional use
You take profit from a Digital System that offers to you the most important features without the necessity
to read a lot of instructions and manuals.
The factory-setup of the system allows you to control your layout by intuition because the system is
self-explaining – even the most important professional features. This level is explained by the short in-
struction that comes with the set and is included to the Lokmaus®2 as it is sold separately.
This more detailed manual tells you everything about the advanced mode for the ‘professional’ players
and model railroaders. We wish you happy hours with your layout controlled by the Lokmaus®2 and
reading this book.
Warning:
Using components of other manufacturers together with ROCO components you risc dama-
ge or malfunctions. We approved a lot of components of other manufacturers that work well. See the list
at the end of this instruction.
Features of the Lokmaus®2
q
controls 99 loco-addresses
q
operates headlights and four additional functions
q
easy control of a loco by speed and direction by a knob
q
easy standard-programming-mode for address, minimum speed acceleration and deceleration de-
lay and maximum speed (CVs 1 to 5)
q
programming the CV29 with important settings for the operation of the loco
q
two digits LED display of the selected address or other information
q
14, 28 and 128 speed steps mode for all locos together or individually selectable for any loco sepa-
rately
q
emergency-stop that stops the complete layout and cuts current supply
q
autoconfiguration of the RocoNet address
q
the system koordinates 31 devices such as the ROCO Lokmaus®2 the switch keyboard etc
q
setup-menu to change a lot of system-features
q
protected mode (programming and emergency-stop can be switched off)
q
operates semaphores and switches if the decoder reacts to loco addresses
q
compatibility to the ‘Lenz digital plus-System’ and other NMRA-systems.
... and additionally in the professional mode:
q
easy programming of the CVs 1-99 with values from 0 to 99
q
big system of menus to setup the system>’s features and functions
q
using a more powerfull amplifier you can read out the decoders in the range from 01 to 99
Plug and play – wiring the Lokmaus®2
The wire of the feeding track is plugged into the connector ‘track out’ of the amplifier. Then you connect
the two pole feeding wire of the amplifier to the two clamps of the transformer. Put the western-plug of
the Lokmaus®2 into the clip called ‘master’ of the amplifier. The scheme fig. 1 on page 2 shows the wi-
ring diagram of all devices of the starting sets. The clip named ‘slave’ must be used for all further Lok-
maus®2. One Lokmaus®2 can be plugged directly to the amplifier, to connect a second, third etc
Lokmaus®2 you need the RocoNet-Y-modul 10758. This is shown by fig. 2 on page 35 that shows the
wiring diagram of the amplifier and three mice.
The RocoNet
RocoNet is called the connection between the amplifier and the Lokmaus®2 that represents the second
generation of the Lokmaus, the Digital System by ROCO. There must be connected one Lokmaus®2 to
the ‘master’ connector of the amplifier. This Lokmaus®2 gets automatically the function of the central
unit of the complete system. It coordinates all devices and generates the track signal. If there is no Lok-
20
