Rockwell Automation Allen-Bradley 1747-SN Скачать руководство пользователя

Страница: 68 / 173

Publication 1747-UM013B-EN-P - January 2005

Scanner Configuration and Programming

4-23

M1 Status File Description

M1 file words 0 through 47 contain the status of all devices on the
scanner’s RIO link.

M1 is a read only file; do not write to this file.

Words 0 to 47 of the M1 file provide the following information:

•

Word 0 (M1:e.0) - general communication status (overall device
fault and communications attempted)

•

Word 2 (M1:e.2) - RIO baud rate status

•

Word 3 (M1:e.3) - complementary device starting address status

•

Word 4 (M1:e.4) - complementary logical image size status

•

Word 5 (M1:e.5) - complementary active device status

•

Word 8 (M1:e.8) - primary/normal device starting address status

•

Word 9 (M1:e.9) - primary/normal logical image size status

•

Word 10 (M1:e.10) - active device status

•

Words 12-15 (M1:e.12 -15) - device fault status

•

Words 16-31 (M1:e.16-31) - primary/normal device retry
counters

•

Words 32-47 (M1:e.32-47) - complementary device retry counters

General Communication Status - Enable Device Fault Bit

Word 0, bit 0 -

is the Enabled Device Fault status bit. When any

enabled device is faulted, this bit is set to 1. A fault may be caused by
a communication problem with a remote device.

General Communication Status - Communication Attempted Bit

Word 0, bit 1 -

is the Communications Attempted status bit. When

RIO communication has been attempted with

all configured devices

this bit is set to 1. There are no further transitions of this bit until a
processor change of state occurs (i.e., Program mode to Run mode or
Test mode, or Test mode to Run mode).

Until this bit is set, all devices in M1 file word 10 (active device status)
appear to be inactive. This bit can be used to condition the Enabled

General Communication Status Word, Word 0

M1:e.0

M1 File

M1 (Status) File W

ord 0

Enabled Device
Fault Bit

Bit Number (decimal)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Allen-Bradley 1747-SN














































































































































































Результаты поиска

Содержание Allen-Bradley 1747-SN

Отзывы:

Похожие инструкции для Allen-Bradley 1747-SN

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 1747-SN, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 1747-SN

Отзывы:

Похожие инструкции для Allen-Bradley 1747-SN

Бренды по названию

Популярные бренды