background image

Robotiq 2-Finger Adaptive Gripper

Instruction Manual

Robotiq inc. © 2016

122

10. Warranty & patent

Robotiq warrants the 2-Finger 85 and 2-Finger 140 Adaptive Robot Grippers against defects in material and workmanship for a period of one year from the
date of shipping from Robotiq when utilized as intended. Robotiq also warrants that this equipment will meet applicable specifications under normal use.

1

successful

 Cycle count : One (1) cycle is defined as an object picking attempt, 

 or not(open or closing onto an object, or

closing on itself). It is calculated in the internal memory of the 2-Finger Adaptive Robot Gripper and can been seen with the
Robotiq User Interface.

During the warranty period, Robotiq will repair or replace any defective 2-Finger Adaptive Robot Gripper, as well as verify and adjust the Gripper free of
charge if the equipment should need to be repaired or if the original adjustment is erroneous. If the equipment is sent back for verification during the
warranty period and found to meet all published specifications, Robotiq will charge standard verification fees.

The unit is considered defective when at least one of the following conditions occurs :

The Gripper fingers cannot close or open;
The Gripper feedback necessary for the robot program is not accessible. 

Parts that come into contact with the work piece and wearing parts such as the finger and palm pads are not covered by the warranty.

This warranty is in lieu of all other warranties expressed, implied, or statutory, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. In no event shall Robotiq be liable for special, incidental, or consequential damages. 

Robotiq shall not be liable for damages resulting from the use of the Robotiq 2-Finger Adaptive Robot Gripper, nor shall Robotiq be responsible for any
failure in the performance of other items to which the 2-Finger Adaptive Robot Gripper is connected or the operation of any system of which the Gripper may
be a part. 

Warranty applies under the following conditions:

Usage respects the operating and storage conditions specified in 

Section 3.3

Proper installation of the Gripper specified in 

 and the following subsections.

Section 3

Usage under normal one-shift operation (40h a week)

Or until a 2 000 000 cycle count has been reached.

Usage respects maintenance specified in 

.

Section 7

Usage respects recommended payload and forces specified in 

.

Section 6.2

Caution
The warranty will become null and void if the :

Unit has been tampered with, repaired or worked on by unauthorized individuals.
Warranty sticker has been removed.
Screws, other than as explained in this guide, have been removed.
Unit has been opened other than as explained in this guide.
Unit serial number has been altered, erased, or removed.
Unit has been misused, neglected, or damaged by accident.

Содержание 2-Finger 140
































































































































Отзывы: