RoboBuilder RQ-110 Скачать руководство пользователя страница 9

Страница: 9 / 89

IR remote controller registration

①

Power-off the smart controller.

②

Press button 2 then, press button P concurrently.

→

You can see LED2 - Green, Blue and Red lights together.

③

Make the IR remote controller close to smart controller towards <IR remote controller receiver>.

④

Press "stop" button in IR remote controller, then LED 2 "Green, Blue and Red" light will be blinking

three times. Now IR remote controller is registered.

※

NOTE

‣

Unregistered remote controller can not control the smart controller.

‣

Each smart controller can memorize 5 remote controller in maximum. If you try to

‣

For the next remote controller registration, you can repeat the above procedures.

Button P

Button 2

IR remote controller

receiver

STOP button

Содержание RQ-110


























































































Результаты поиска

Содержание RQ-110

Отзывы:

Похожие инструкции для RQ-110

Бренды по названию

Популярные бренды

RoboBuilder RQ-110, Быстрый старт

Результаты поиска

Содержание RQ-110

Отзывы:

Похожие инструкции для RQ-110

Бренды по названию

Популярные бренды