EM-S
ERIES
I
NSTALLATION
, O
PERATION
AND
S
ERVICE
M
ANUAL
46 of 71
10.5 Heat Demand Control Wirin
g
The heater inp
u
t can be controlled by any one of the
follo
w
ing heat demand control de
v
ices (control
de
v
ices are
w
ired to central heaters only):
10.5.1 Zone Sensor
The zone sensor (P/N 10081530) offers a
u
tomatic
control of heater inp
u
t. Heater(s) mod
u
lates based
on difference bet
w
een sensed air temperat
u
re and
the temperat
u
re setpoint. Heater mod
u
lation in
response to air temperat
u
re changes is immediate.
Setpoint is adj
u
sted
w
ith the slide bar adj
u
stment at
the bottom of the sensor. ON/OFF s
w
itch (
u
sed to
disable heater operation or reset heater from locko
u
t)
is located on the side of the sensor.
See Page 41,
Figure 21
for
w
iring details.
10.5.2 Thermostat
A thermostat offers a
u
tomatic control of heater inp
u
t.
The heater control is designed for
u
se
w
ith a
standard 2-
w
ire or 4-
w
ire lo
w
v
oltage electronic
thermostat (not for
u
se
w
ith thermostats that ha
v
e a
heat anticipator). Typical
w
iring connects the R and
W
w
ires to the heater control and does not connect
the Y (cooling) and G (fan)
w
ires to the heater
control.
The heater can be
u
sed
w
ith thermostat, 24V (p/n
90425100) if set to 5 cycles per ho
u
r. Any other
electronic thermostat
w
itho
u
t heat anticipator can be
u
sed if set to 5 or 6 cycles per ho
u
r.
On the control, the T24 and T25 (R and W) terminals
s
u
pply 24 V to po
w
er an electronic thermostat.
See
Page 46, Figure 25
for
w
iring details. Cons
u
lt the
factory for other thermostat
w
iring config
u
rations.
Heater(s) mod
u
lates based on heater and thermostat
cycle timing, history and desired setpoint by
u
sing a
pre-programmed algorithm. When
u
sing thermostat
control, heater mod
u
lation response to rapid air
temperat
u
re change is not immediate. Thermostat
control is not recommended for
u
se in areas
w
ith
freq
u
ent or high air changes.
It is important to note that d
u
ring normal operation,
heater cycle contin
u
es beyond meeting thermostat
setpoint.
FIGURE 25: Thermostat Control Wirin
g
Dia
g
ram
*OPTIONAL
SWITCH
SATELLITE HEATER CONTROL
J10 JUMPER POSITION
SHOWS "SATELLITE" DESIGNATION.
MODULATION CONTROL WIRING
TO ADDITIONAL SATELLITE
HEATER CONTROL TERMINALS
T28 AND T29.
MODULATION CONTROL WIRING
TO SATELLITE HEATERS
CENTRAL HEATER CONTROL
T31
T29
T19
T18
T16
T14
T27
T25
T30
T28
T17
T15
T13
T26
T24
T31
T29
T19
T18
T16
T14
T27
T25
T30
T28
T17
T15
T13
T26
T24
R
W
T
J10
W
R
-
+
-
+
-
+
OUT
RA
TE
FIRING
IN
RA
TE
FIRING
EXT
. PO
T
GND
WIPER
HIGH
GND
BA
R
SLIDE
GND
THERMIS
T
OR
INPUT
ANAL
OG
THERMOSTAT
J10
W
R
-
+
-
+
-
+
OUT
RA
TE
FIRING
IN
RA
TE
FIRING
EXT
. PO
T
GND
WIPER
HIGH
GND
BA
R
SLIDE
GND
THERMIS
T
O
R
INPUT
ANAL
OG
THERMOSTAT
J10 JUMPER POSITION
SHOWS "CENTRAL"
DESIGNATION AND
"THERMOSTAT"
CONTROL METHOD.
* Separate on/off s
w
itch is optional for "satellite" heaters (install at
u
ser le
v
el).
On/Off s
w
itch is
u
sed to disable heater operation or reset a heater that is in "locko
u
t" mode.
If on/off s
w
itch is not desired, lea
v
e j
u
mper
w
ire bet
w
een R and W terminals in place.
Содержание Energytube EM-115
