manualshive.com logo in svg

RKI Instruments 04 Series, Руководство оператора, Страница: 43 / 98

Поделиться
Скачать
RKI Instruments 04 Series Скачать руководство пользователя страница 43

SC-04

Chapter 5: User Mode and Calibration • 43

Performing a Span Adjustment

1. While in User Mode, press AIR to scroll to 

GAS CAL

.

2. Press and release POWER MODE. The 

AIR

 item appears.

3. Use AIR to scroll to the 

A-CAL

 item.

4. Press and release POWER MODE. The display shows the gas and its assigned calibration 

value (see pg.47 if the calibration value does not match the calibration gas cylinder’s 

concentration).  

5. For toxic gas cylinders, it is important to vent the regulator while installing it onto the 

cylinder. Venting the regulator during installation helps prevent air from getting into the 

cylinder and degrading the gas. Open the regulator by turning the knob counterclockwise 

and install it onto the cylinder.

6. Press and release POWER MODE.
7. The gas reading flashes and the bottom of the screen alternates between “APPLY” and “A-

CAL”.

NOTE:

To back out of the gas application screen without performing the calibration, press 

and release AIR and POWER MODE together.

8. Turn the regulator knob counterclockwise to open the regulator.
9. Allow the gas to flow for 1 minute for all gases except Cl

2

 and NH

3

. Allow Cl

2

 and NH

3

 

gas to flow for 2 minutes.

10. Press and release POWER MODE.

  

  

GAS  CAL

  

  

A-CAL

 SO2

    5.00

  

A-CAL

ppm

 SO2

    0.00

  

A-CAL

ppm

 SO2

    0.00

  

APPLY

ppm

Содержание 04 Series



































































































Отзывы:

Нет отзывов