manualshive.com logo in svg

RKI Instruments 04 Series, Руководство оператора, Страница: 19 / 98

Поделиться
Скачать
RKI Instruments 04 Series Скачать руководство пользователя страница 19

SC-04

Chapter 3: Measuring Mode • 19

5. If 

Password Protection

 is turned 

On

 (factory setting is 

Off

) using the 04 Series Setup 

Program, a user-set password is required to perform a demand zero. When the password 

screen appears, adjust each digit with the AIR button and press and release the POWER 

MODE button to move on to the next digit. Once the password is entered, the instrument 

sets the fresh air reading.

Turning Off the SC-04

1. Press and hold POWER MODE.
2. OFF appears on the display and the buzzer pulses for about five seconds (if 

KEY.TONE

 

is set to 

ON

 in User Mode).

3. Release the button when OFF disappears from the display. 
4. If 

Password Protection

 is turned 

On

 (factory setting is 

Off

) using the 04 Series Setup 

Program, a user-set password is required to turn off the SC-04. When the password screen 

appears, adjust each digit with the AIR button and press and release the POWER MODE 

button to move on to the next digit. Once the password is entered, the instrument shuts off.

Measuring Mode Operation

When the SC-04 completes its startup sequence, it is in Measuring Mode. In Measuring Mode 

the SC-04 continuously monitors the sampled atmosphere and displays the gas concentration. 

The SC-04 is in Normal Operation if there are no alarm indications.

Heart Symbol: The heart symbol in the top right corner of the LCD indicates the operation 

status and flashes when normal. A microprocessor error causes the heart symbol to stop 

flashing or to disappear.
Check Mark: If 

BP.RMDR

 is set to 

ON

 and if a bump test is not due, a check mark appears in 

the lower left corner of the LCD.
“S”: If the instrument is operating in Stealth Mode, an “S.” appears at the bottom of the LCD.
Backlight: In a low-light environment, press and release either button to turn on the display 

backlight. See pg.58 to program backlight duration. 
Confirmation/Non-Compliance Indicator: If the 

BEEP

 item in User Mode is set to anything 

other than 

OFF

, the SC-04 gives periodic indications to confirm that it’s operating or to 

indicate a non-compliance (see pg.57).

   0000

  

PASS-W

   0000

  

PASS-W

  SO2

    0.00

       S.

ppm

Содержание 04 Series



































































































Отзывы:

Нет отзывов