background image

S-2C

6

Connector

QTY

C-1

2

Use C-1 connector to secure each 

outside corner. Loosen set screws on 

profiles and adjust position to fit holes in 

C-1 connectors.  Make sure all profiles line up flush 

against each other. Secure with three bolts. Repeat on other side. 

Check inside corners to ensure B-7 

connector is still in proper position. 

If it needs adjusting, repeat steps 6.6B 

and 6.6C until each corner is set.

6.5

Continue working from outside to install 

panels a shown. Remove plastic film 

from both sides of two W-3 and 

two W-4 panels. Fit each 

panel into channel in 

profiles, placing side 

marked “ UV Resistant” 

facing outside. 

6.6A

6.6B

6.6C

From outside fit F-7 profiles into each side of back. Arrange the profile so channel lines up 

with tops of panels and the set screws on each end are visible. Begin with either right or left 

side. Profile side fits against cut angle of F-3 profile. One 

end touches top of gutter and the top end 

touches edge of F-2 center profile. 

Position both F-7 profiles. 

W-4

2

Panel

QTY

24” x  30 ¾”

W-3

2

Panel

QTY

24” x  15 ¼”

W-3

W-3

W-4

W-4

NOTE: VIEW FROM OUTSIDE.

NOTE: VIEW FROM OUTSIDE.

NOTE: VIEW FROM OUTSIDE.

NOTE: VIEW FROM INSIDE.

F-3

F-7

F-7

F-3

F-2

F-7

NOTE: Panels will not fit completely to end of channels. 

There will be some space to allow for temperature changes.

WARNING: The corners of W-3 and W-4 panels 

are sharp. Use extreme caution when handling.

G-1

F-7

F-6

C-1

WWW.RSIWW.COM

29 of 46 

G-1

F-6

B-7

F-7

Содержание Monticello 8x20
















































Отзывы: