RIDGID 918-i, Руководство пользователя

Страница: 15 / 68

999-998-676.10_REV. C 13
918-I Heavy Duty Roll Grooving Machine
• With the spindle lock engaged, use a wrench to
tighten the draw bolt.
• Release pressure on the spindle lock pin, allowing
to retract.
• Pull drive shaft assembly forward. Insert front half of
coupling onto back half. Insert drive shaft assembly
through the bearing retaining nut, aligning hex with
opening in coupling.
• Use spanner wrench to tighten the drive shaft bear-
ing retaining nut.
• Tighten transmission coupling set screws.
• Close motor and transmission cover.
Do not use groover with cover removed or
open.
4. Installing Groove Roll:
• With upper roll housing fully raised and drive shaft
in place, insert groove roll into upper roll assembly
and fully insert upper roll shaft through bearings and
groove roll.
• Tighten groove roll set screw into detent on upper
roll shaft.
5. Using a grease gun, grease the drive shaft through
the fitting on the side of the Groover.
Changing from Solid Drive Shaft Roll
Set to Two-Piece Drive Shaft
1. Removing Groove Roll:
• Fully raise the upper roll housing by moving the
pump release lever to the return position, away
from the operator.
• Loosen groove roll set screw (Figure 11) . Grasp
groove roll and remove upper roll shaft and groove
roll from Groover
(Figure 12) .
2. Changing Solid Drive Shaft Roll Set to Two-Piece
Drive Shaft:
• Open motor and transmission cover.
• Use 3 /
16
" hex key to loosen the two screws on the
transmission coupling (Figure 13) .
• Use the box wrench to remove the drive shaft
bearing retaining nut (Figure 14) .
• Remove the drive shaft (Figure 15) .
• Remove the front half of the coupling.
• Assemble proper drive roll to drive shaft (two-
piece style) with draw bolt hand-tight.
• Insert two-piece drive shaft assembly into 918-I.
• Manually rotate the drive shaft while applying pres-
sure to the spindle lock pin until the lock pin engages
the spindle lock hole in the drive shaft assembly.
• With the spindle lock engaged, use a wrench to
tighten the draw bolt.
• Release pressure on the spindle lock pin, allowing
to retract.
• Pull drive shaft assembly forward. Insert front half of
coupling onto back half. Insert drive shaft assembly
through the bearing retaining nut, aligning hex with
opening in coupling.
• Use spanner wrench to tighten the drive shaft
bearing retaining nut.
• Tighten transmission coupling set screw.
• Close motor and transmission cover.
Do not use groover with cover removed
or open.
3. Installing groove roll:
• With upper housing fully raised and drive shaft in
place, insert groove roll into upper roll assembly and
fully insert upper roll shaft through bearings and
groove roll.
• Tighten groove roll set screw into detent on upper
roll shaft.
4. Using a grease gun, grease the drive shaft through the
fitting on the side of the groover.
Accessories
Only the following RIDGID products have
been designed to function with the 918-I Roll Groover.
Other accessories suitable for use with other tools may
become hazardous when used on this Roll Groover.
To prevent serious injury, use only the accessories listed
below.
NOTE: A Roll Set consists of a Groove Roll and a Drive Roll.
Catalog
No. 918-I Accessories
48405 Roll Set for 8"
−
12" Sch. 10, (8" Sch.40) with Carrying Case
48407 Roll Set for 1 1 /
4
" to 1 1 /
2
" Sch. 10/40 with Carrying Case
48412 Roll Set for 1" Sch. 10/40 and 1 1 /
4
" to 1 1 /
2
" Sch. 10/40 with
Carrying Case
48417 Roll Set for Copper (2" − 6")
76822 English Diameter Tape
76827 Metric Diameter Tape
Pipe Stands (See Ridge Tool Catalog)
WARNING
WARNING
WARNING