Ricoh SP 230SFNw Скачать руководство пользователя | Manualshive

Страница: 119 / 255

background image

3-1

Confidential

CHAPTER 3 DISASSEMBLY/REASSEMBLY

1. SAFETY PRECAUTIONS

To avoid creating secondary problems by mishandling, follow the warnings and precautions

below during maintenance work.

• Be careful not to lose screws, washers, or other parts removed.
• Be sure to apply grease to applicable positions specified in this chapter.
• When using soldering irons or other heat-generating tools, take care not to accidentally

damage parts such as wires, PCBs and covers.

• Static electricity charged in your body may damage electronic parts. When transporting

PCBs, be sure to wrap them in conductive sheets.

• When replacing the PCB and all the other related parts, put on a grounding wrist band and

perform the job on a static mat. Also take care not to touch the conductor sections on the
flat cables or on the wire harness.

• After disconnecting flat cables, check that each cable is not damaged at its end or

shortcircuited.

• When connecting flat cables, do not insert them at an angle. After insertion, check that the

cables are not at an angle.

• When connecting or disconnecting harnesses, hold the connector body, not the cables. If

the connector is locked, release it first.

• After a repair, check not only the repaired portion but also harness treatment. Also check

that other related portions are functioning properly.

• Forcefully closing the front cover without mounting the toner cartridge and the drum unit

can damage the machine.

• After assembly, it is recommended to conduct dielectric strength test and continuity test.
• When mounting the inlet, check that the inlet is housed in the frame completely and that

the harness is not caught in the frame.

• The insulation sheet should not be damaged.
• After a repair, update the firmware to the latest version.

WARNING

Some parts inside the machine are extremely hot immediately after the machine is used.

When opening the front cover ASSY or back cover to access any parts inside the

machine, never touch the shaded parts shown in the following figures.

WARNING

When removing the Low-voltage power supply, do not touch it

within

3 minutes

after disconnecting the AC cord as it may cause

an electric shock due to the electric charge accumulated in the

capacitor.

«
...
117
118
119
120
121
...
»

Содержание SP 230SFNw
































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SP 230SFNw

Бренд: DataCard Страницы: 8

Бренд: Canon Страницы: 358

Бренд: VASTEX Страницы: 15

VarioPrint 1055

Бренд: OcÃ© Страницы: 194

Бренд: Oce Страницы: 12

Бренд: Unimark Страницы: 38

Бренд: Canon Страницы: 32

Бренд: Ricoh Страницы: 4

Бренд: BIXOLON Страницы: 59

Бренд: Wang Страницы: 181

Бренд: Ricoh Страницы: 156

Бренд: Oki Страницы: 80

16C0365 - 5500 MFP

Бренд: Lexmark Страницы: 88

Бренд: Ricoh Страницы: 24

Бренд: Xerox Страницы: 150

Бренд: SAGEMCOM Страницы: 146

Posligne ODP-1000

Бренд: AURES Страницы: 4

Бренд: Pantum Страницы: 155

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды