Ricoh FAX7000L Скачать руководство пользователя страница 78

Страница: 78 / 377

3. Hard Disk Dump

If there is a missing file on the hard disk or another hard disk problem, and the hard disk maintenance routines

did not help, the best thing to do is replace the hard disk, or the SPU or SCU. However, some information can

be obtained by making a hard disk dump. To do this requires co-ordination with Ricoh Technical Services. Tell

them the following:

• How many files remain on the disk.

• What file numbers are missing
• What other good files remain on the disk (make a File List)

Then in a few days, Ricoh Technical Services should inform which cylinder and block number to enter. Print the

report and send it to Ricoh Technical Services for analysis.

1. Enter the service mode. See page 2-18.

2. When the service mode menu is displayed, enter 03 at the ten-key pad.

3. When the RAM menu is displayed, press 2.

4. Enter the cylinder number and block number of interest. If you make an error, press Yes and go to step 3.

5. Press Start. The dump list is printed.

6. Press Function if all service mode operations have been finished.

2-26

Содержание FAX7000L


























































































































































































































































































































































































Результаты поиска

Содержание FAX7000L

Отзывы:

Похожие инструкции для FAX7000L

Бренды по названию

Популярные бренды

Ricoh FAX7000L, Руководство по обслуживанию на месте

Результаты поиска

Содержание FAX7000L

Отзывы:

Похожие инструкции для FAX7000L

Бренды по названию

Популярные бренды