Ricoh FAX7000L Скачать руководство пользователя страница 54

Страница: 54 / 377

1. Indicators

Transmitting Indicator

Lights when the machine is sending a fax message.

Receiving Indicator

Lights when the machine is receiving a fax message.

Storing Indicator
Lights when the machine is storing a fax message to the

hard disk.

Confidential File Indicator

Lights when a confidential message has been received.

Receive File Indicator
Lights when a message was received but could not be

printed because the printer was out of order (copy jam,
no toner, or no paper).

Memory Full Indicator
Blinks when the remaining memory space falls below

5%, and lights when there is no more space on the hard
disk.

Line Fail Indicator
Blinks when transmission fails.

Call Service Indicator

Blinks when the machine diagnostics detect a problem

that requires service.

Clear Original Indicator

Blinks when a document has jammed in the scanner.

Clear Copy Indicator

Blinks when paper has jammed in the printer.

Add Paper 1 Indicator

Blinks when the upper cassette is almost empty, and

lights when it is empty.

Add Paper 2 Indicator

Blinks when the lower cassette is almost empty, and

lights when it is empty.

Add Toner Indicator

Blinks when the toner cartridge is almost empty, and

lights when it is empty.

Toner Collection Indicator

Blinks when the toner collection tank is almost full, and

lights when it is full.

Close Cover Indicator

Blinks when a cover is open.

Replace Master Indicator

Blinks when it is time to replace the master unit.

2-2

Содержание FAX7000L


























































































































































































































































































































































































Результаты поиска

Содержание FAX7000L

Отзывы:

Похожие инструкции для FAX7000L

Бренды по названию

Популярные бренды

Ricoh FAX7000L, Руководство по обслуживанию на месте

Результаты поиска

Содержание FAX7000L

Отзывы:

Похожие инструкции для FAX7000L

Бренды по названию

Популярные бренды