Rice Lake Ishida OMNi-4000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

background image

Ishida OMNi-4000 Error Codes and Troubleshooting

15.9 NO ERROR CODES

Section

Symptom

Phenomenon

Response or Check

Power

Wrapper is dead - no response

Single beep from wrapper at power up. Lamp is lit on
the temperature control dial and red status LEDs on
sensors are lit.

1. Rear panel fuses: F13, F14 (250V, 8A)
2. Power Supply (right side of printer) fuse: F1

(250V, 3.6A 5x20 Ceramic)

3. Power Supply (2H113W, right side of printer)

Wrapper resets

Wrapper resets during operation

1. Check 3-phase power:

a. Low leg(s)
b. Fluctuating

2. Power Supply (2H113W, right side of printer) p/n 100015

Lamp on temperature control dial is not lit.

1. Rear panel fuses: F11, F12 (250V, 4A)
2. Loose connections at Temperature Controller terminals
3. Temperature Controller
4. Check the thermistor probe.

a. Check connections and terminal lugs at the Temperature

Controller.

b. Check continuity. If no continuity check or resoldered the terminal

lugs on the wires.

c. Replace the thermistor probe.

5. Relay - connections are bad or intermittent

Lamp on temperature control dial is lit.

1. Thermal TCO fuse (in-line with Heating element)
2. Heating element
3. Loose connections at Temperature Controller terminals
4. Temperature Controller

Exit
Conveyors

No discharge conveyor operation.

1. Rear panel fuse: F26 (250V, 1A)
2. P-858B fuse: F4 (250V, 5A, 5x20)
3. Check condition of drive belt (transfer conveyor)

and drive chain (heater conveyor.

4. Check drive motors.

Film

No heat in film roll area.

1. Film Roll Heater fuses (located below the main rear panel):

F1, F2 (250V, 8A)

2. Film Roll Heater

No Film Roll motor assist.

Both Left and Right motors do not turn.

P-858B fuse: F3 (250V, 5A, 5x20)

Film Waiting position is too far back.

The leading edge of the film waiting to be fed into the
wrap area is too far back - too close to the Polished
Roller.

1. The Cutter Clutch is slow. Check the clutch for contamination
(grease, dirt, etc.)
2. Replace the Clutch.
3. Change the Film Position timing setting to stop the film later.

[Test menu, Wrapper Setup, page 2]

No heat at package seal heater.

Sealing
Heater

Rev. Feb 2015

35/40

Yellow highlights indicate updates

«
...
33
34
35
36
37
...
»

Содержание Ishida OMNi-4000









































Отзывы:

Нет отзывов

Похожие инструкции для Ishida OMNi-4000

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: Panasonic Страницы: 9

Бренд: Ecco Страницы: 3

Бренд: JB Systems Страницы: 12

Бренд: Mandam Страницы: 9

Бренд: Gardol Страницы: 260

Бренд: York Fitness Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: 4iQ Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды