Rice Lake Ishida OMNi-4000 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 40

background image

Ishida OMNi-4000 Error Codes and Troubleshooting

15.8 ERROR CODE (1600 - )

No.

Message

Symptom or Phenomenon

Response or Check

1600 "A MEMORY SETUP OF THE SCALE

IS UNUSUAL"

Scale (A/D, P-930) memory settings are abnormal. Recalibrate the scale.

If the error cannot be resolved or recurs later replace the
A/D board P-930.

1601 "SPAN ADJUSTMENT OF THE SCALE

INCOMPLETE"

Scale (A/D, P-930) span adjustment incomplete.

NOTE: Ignore sub-error numbers, all indicate the
same problem.

Recalibrate the scale.
If the error cannot be resolved or recurs later replace the
A/D board P-930.

1602 "INITIALIZATION THE SCALE IS NOT

COMPLETED"

Scale (A/D, P-930) initialization has not been
completed.

Recalibrate the scale.
If the error cannot be resolved or recurs later replace the
A/D board P-930.

1618 "CHECK THE SCALE"

Check that nothing is in touch with weighing
conveyor.
(Air currents, vibration)

Remove the weighing conveyor to check if anything is touching the
weighing conveyor and remove foreign objects if any.
Also check for air currents or vibration.

1619 "TAKE THE ARTICLE ON THE SCALE

PLATE"

An item remains on the scale.

1. Remove item from the weighing platter.
2. Check for mechanical obstructions at the scale and conveyor.

The scale zero calibration is out of range.

1. Recalibrate the scale.
2. Replace the load cell.
3. Replace the A/D board.

1621 "THERE IS NO RESPONSE FROM

THE SCALE"

There is no response from the scale (A/D, P-930).
Restore power after checking scale connection
01: Invalid text
02: Initializing
03: Out of range
04: Unstable
05: Unable to change between A/D
06: Calibration adjustment is not complete
07: Unable to send (Scale debug response)
08-16: WPL
17: Upper/lower limit error
18: Check scale
19: Remove item from the weighing platter
20: Power failure detected
21: No response from the scale board
(connection error)
22: Communication error (connection error)
23: Communication error (connection error)

Check harness, connector
Replace P-930(XJ1,4,5) - X292 - X291 - P-910(XJ8)

1622 "COMMUNICATION IMPOSSIBLE

WITH THE SCALE"

Cannot communicate with the scale (A/D, P-930)
Restore power after checking scale connection.

Check harness, connector
Replace P-930 (XJ1,4,5)-X292-X291-P-910(XJ8)

Rev. Feb 2015

33/39

Yellow highlights indicate updates

«
...
31
32
33
34
35
...
»

Содержание Ishida OMNi-4000









































Отзывы:

Нет отзывов

Похожие инструкции для Ishida OMNi-4000

Бренд: Rath Страницы: 3

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Jasco Страницы: 2

Бренд: T&D Страницы: 28

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

Бренд: MÄDLER Страницы: 4

Бренд: BRAND Страницы: 21

Бренд: Milestone Страницы: 40

Firefly 808 Universal

Бренд: Phonic Страницы: 27

Ti-Lite Carbo AirBlock 351

Бренд: Harken Страницы: 2

Be strong NS 200X

Бренд: Nautilus Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды