Rice Lake Ishida OMNi-4000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

background image

OMNi-4000 Error Codes and Troubleshooting

15.4 ERROR CODE (0400 - )

No.

Message

Symptom or Phenomenon

Check

OMNi-3000

0450 LEFT SIDE FILM LOADING DOOR IS

OPEN

Door open during operation

1. Front-Left side door is open.
2. Harness is damaged or short-circuited P-857 -> P-858 (No. A) -> P-858 (No. C).
3. Harness damaged between P-857 and electromagnetic contactor.
4. Harness damaged between P-858 (No. C) and the front-left side door.
5. Harness damaged between electromagnetic contactor and thermal relay.
6. Harness damaged between electromagnetic contactor and front-left side door.
7. P-857 error or fuse(F1, F2, F3)
8. P-858 (No. C) error.
9. Electromagnetic contactor error.
10. Thermal relay error.
11. Front-left side door error.
12. Rear Panel fuse(F21, F22, F23)

1150-0008

0460 ITEMS WERE NOT THROWN IN

Tray cannot be fed.
Fed about 10 mm.
Remove the tray on halfway.

1. They tray did not move onto the lift properly.
2. Feed stops before the normal position.
3. Lift height is too low.
4. Lift height is too high.
5. Tray length is too short.
6. Tray height is too low.
7. Item sensor sensitivity incorrectly adjusted.
8. Item sensor error.
9. P-857 error.
10. P-858 (No. A) error.
11. One chip CPU (on the P-857) error.

1133

0461 FILM OVER AT RIGHT SIDE

Film Over (Left--->Right)

1. Film over error.
2. Film waste detected.
3. Film sensor (front/right) sensitivity incorrectly adjusted.
4. Film sensor (rear/right) sensitivity incorrectly adjusted.
5. Film sensor (front/right) error.
6. Film sensor (rear/right) error.
7. Film count sensor error.
8. Film cutter clutch brake (left) error.
9. Film cutter original position sensor (left) error.
10. P-857 error.
11. P-858 (No. B) error.

1127-0001

0462 FILM OVER AT LEFT SIDE

Film Over (Right--->Left)

1. Film over error.
2. Film waste detected.
3. Film sensor (front/left) sensitivity incorrectly adjusted.
4. Film sensor (rear/left) sensitivity incorrectly adjusted.
5. Film sensor (front/left) error.
6. Film sensor (rear/left) error.
7. Film count sensor error.
8. Film cutter clutch brake (right) error.
9. Film cutter original position sensor (right) error.
10. P-857 error.
11. P-858 (No. C) error.

1127-0002

Rev. Feb 2015

17/

40

Yellow highlights indicate updates

«
...
15
16
17
18
19
...
»

Содержание Ishida OMNi-4000









































Отзывы:

Нет отзывов

Похожие инструкции для Ishida OMNi-4000

Бренд: THORLABS Страницы: 44

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: iFIT Страницы: 11

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jacto Страницы: 64

Бренд: Nederman Страницы: 255

Бренд: Omlet Страницы: 60

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

LSP400 LED Series

Бренд: WE-EF Страницы: 6

Бренд: Yamaha Страницы: 48

COLORado Ridge IP

Бренд: Chauvet Страницы: 8

ColorSource Fresnel V

Бренд: ETC Страницы: 16

Бренд: Leister Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды