Rice Lake Ishida OMNi-4000 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 40

background image

Ishida OMNi-4000 Error Codes and Troubleshooting

15.5 ERROR CODE (0600 - )

No.

Message

Symptom or Phenomenon

Check

0633 "THE PROBLEM AROSE IN THE

APPLICATOR"

There is no Applicator program (firmware)
[Sub-error]
-0000 Bad checksum or no application.
-0001 The application ran too quickly.

1. Download the firmware file to the P-916 Applicator Controller board.

a. Test Menu, Program Download.
b. Select firmware (B0509A) - yellow highlight.
c. Execute.

2. If the same error recurs, replace P-916.

After replacing the P-916 board perform the following steps:
a. Download firmware to P-916. See step 1 above.
b. Initialize the Applicator [Test Menu, Applicator Adjustment,

page 2].

c. After initialization, confirm the prompt to send backup

settings from main memory.

d. If no backup is available, manually program settings in

Test Menu, Applicator Adjustment, page 1.

0650 THERE WAS NO RESPONSE FROM

THE APPLICATOR

Unable to communicate between the console and
applicator.
[OK]
-> Cut communication with the applicator. Operate
without the applicator.
[RETRY]
-> Check connection with the applicator. The error
is cleared if connection can be confirmed.
[Remarks] It is possible to operate without the
applicator after pressing the [OK] button.

Press the [RETRY] key and attempt communication. The consider the
following causes if the error does not clear:
1

）

Unplugged connector: P-916: XJ17, XJ27 (0650-0017)

2

）

Shorted harness

3

）

Board P-910 malfunction

4

）

Board P-918 malfunction

5

）

Board P-916 malfunction

Rev. Feb 2015

28/

40

Yellow highlights indicate updates

«
...
26
27
28
29
30
...
»

Содержание Ishida OMNi-4000









































Отзывы:

Нет отзывов

Похожие инструкции для Ishida OMNi-4000

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: GE Страницы: 24

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: Gardena Страницы: 19

Бренд: Jackco Страницы: 6

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Gardigo Страницы: 32

Бренд: JBSYSTEMS Light Страницы: 17

Бренд: zapco Страницы: 14

Бренд: Sweet Sound Electronics Страницы: 6

Бренд: DC Страницы: 2

INFINA DL-AC-FLEX2-RGBW

Бренд: Jesco Страницы: 7

Бренд: Lanta Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды