Rice Lake Ishida OMNi-4000 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 40

background image

Ishida OMNi-4000 Error Codes and Troubleshooting

15.5 ERROR CODE (0600 - )

No.

Message

Symptom or Phenomenon

Check

0608 "OPERATION OF THE APPLICATOR

STOPPED"

Power to the applicator was shut off during
operation.

NOTE:

This message may be displayed rather

than a Door Open or E. Stop message.

1. Confirm all Doors are closed.
2. Release the Emergency Stop switch.

NOTE

: Be sure all doors are closed and E. Stop is released after this

error occurs. Otherwise the error will not clear.
3. Check the input voltage (AC 200V) to the power unit (3H138W)

located on top of the wrapper.

4. Check the output voltage (DC 24V) from the power unit (3H138W).
5. Check connections at P-916: XJ18 to P-857: J5 + Safety Contactor.
6. Check continuity at Safety Contactor terminals 13-14.

NOTE

: If error 0409-0000 preceeds this error due to missing 24VDC,

then 0608-0000 will follow combined with the status message
"Printer Door is Open".

0609 "ABSORPTION OF LABEL WAS NOT

COMPLETED"

Applicator failed to pickup the label from the printer. 1. Press [RETURN] button, remove label.

2. Clean the blue Applicator sponge.
3. Check the condition of the blue Applicator sponge - replace if

worn or damaged.

4. Check operations of two suction fans, clean or replace as needed.
5. Labels are not flat. Labels curl due to defect or moisture / humidity.
6. Adjust the label position for better pickup:

a. Check position of Roller Table supporting the printed labels.

It must be horizontal, not tipped forward.

b. Feed labels farther out.

[Test menu, Printer Adjust, page 2, Feed (Stop)]

7. Adjust the Applicator pickup position:

a. Adjust height of applicator head

[Test Menu, Applicator Adjust, "Down By"]

8. If both suction fans are not turning check:

a. Loose or shorted cables and connections.
b. Verify voltage: 24VDC at XJ2 (

XJ3?

) of P-916 Applicator Control

board (located on top of the wrapper).

Rev. Feb 2015

25/

40

Yellow highlights indicate updates

«
...
23
24
25
26
27
...
»

Содержание Ishida OMNi-4000









































Отзывы:

Нет отзывов

Похожие инструкции для Ishida OMNi-4000

Бренд: Ecco Страницы: 4

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: Jacobsen Страницы: 6

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды