![Rheavendors Group Cino XS Grande Pro VHO Скачать руководство пользователя страница 50](http://html1.mh-extra.com/html/rheavendors-group/cino-xs-grande-pro-vho/cino-xs-grande-pro-vho_installation-and-maintenance-manual_1451225050.webp)
13.15. regulate the speed
of mixers
13.16. choose the
quantity of break
numbers
13.17. time tests
13.18. determine the
suction fan time
13.19. remove water
13.20. return some
material under guarantee
the rotation speed of the motors of product mixers can be adjusted
between 15,000 r.p.m. and 5,000 r.p.m.; the drink quality of
instant products depends a lot upon the action of the fans of
mixers: instant chocolate generally requires a long mixing time at
the maximum speed for dissolution in water whereas instant tea
shall not be mixed to get a drink quality without any bubble on the
surface;
if instant products can be hardly dissolved in water, it may be of
use to stop the product dispensing cycle from the product canister
for a short time; the water flowing into the mixing bowl will have
the time necessary to remove any product build-up;
to check the rotation time of a product motor and a mixer fan or
the activation time of a solenoid valve during the programming
phase, when the display shows
“PRODUCT
N”
or
“WATER
N
time”
or
“MIXER
N”,
press the
“PROG”
key: the device will be activated
for the programmed time;
to remove the residual powder of instant products from inside the
machine, it is recommended to use the value in minutes you have
already programmed (three); if you should use particularly volatile
products, increase the time to five (and more) minutes;
to discharge water from the circuits of the machine:
attention
these components may be very hot
even if the machine is off;
- detach the water supply; disassemble the rear panel;
- connect a 6x9 tube with the solenoid valve intended to discharge
the pressure boiler (see 05.35.) and convey water into a min. 3-l
bucket to be placed on the floor;
- power on the machine by means of the service key, access the
programming mode, scroll as far as the items
“miscellaneous”
and
“
uninstallation
”
;
- press
“
4
”,
press
“
5
”
; the machine pump will start to discharge
water from the pressure boiler and the tubes into the bucket;
- the time required to let water out completely is over six minutes;
attention
- wait for the cycle to come to an end; the display will show:
- power off the machine;
- remove the plug fastening screw, extract the air break outlet
hose, empty it into the water bucket;
- re-insert the plug into the tube and remount it onto the machine
by means of the fastening screw;
- remove the tube from the drain solenoid valve of the pressure
boiler;
- remount the rear panel of the machine;
if you should return any material under guarantee that is either
defective or not in compliance with your requirements, fill in the
form
“MOD
. PO 19.01/2B Materials under guarantee
–
Authorisation to
return”
and send it to the fax number above to
apply for authorisation; only after having received the authorisation
form signed and numbered, you are permitted to send the goods at
your expenses to the address specified by the form;
DEINSTALLATION
4=START
CONNECT BOILER
TUBE 5 = >
DEINSTALLATION
END DEINSTAL.
SWITCH OFF
Cino XS grande PRO VHO
by
MAN2100154 rel. 00 dated 04.11.2013 page no. 50 of 51 pages
www.rheavendors.com tel: 0039 02 966 551 fax: 0039 02 96 55 086 e mail: rheavendors@rheavendors.com
exclusive property of rheavendors group