9
3. Carefully lower the saw head down to
align the saw blade with the pattern
line. Position the saw blade to the left,
center or right side of the “pattern line”
depending on your preference for the
laser line location.
4. With the saw plugged in, turn on the
laser guide. Your saw has been preset
with the laser line to the left side of
the blade.
5. Slide the cutting head forward enough
so that the laser line is visible on the
front of the board.
6. Looking at the front of the board, if the
laser line is not parallel to the “pattern
line” please follow the instructions listed
below under “Front line” paragraph.
7. Looking at the top of the board, if the
laser line is not parallel to the “pattern
line” please follow the instructions listed
below under “Top line” paragraph.
B.
Adjusting the Position of the Laser
Line (Fig. 22, 23, 24)
Front line (Fig. 22, 23)
If the laser line is angled from left to right,
turn the laser vertical adjustment knob (1)
counterclockwise to align the laser line
parallel with pattern line. If the laser line
is angled from right to left, turn the knob
clockwise to align the laser line parallel with
pattern line.
Top line (Fig. 22, 24)
If the laser line is angled from left to right,
turn the laser horizontal adjustment knob (2)
clockwise to align the laser line parallel with
pattern line. If the laser line is angled from
right to left, turn the knob counterclockwise
to align the laser line parallel with pattern
line.
WARNING! When making laser line
adjustments, keep fingers away from
the ON/OFF trigger switch to prevent
accidental starting and possible serious
injury.
After performing the above adjustments,
visually check that both the front and top
laser lines are parallel with pattern line.
NOTE:
●
Laser line is calibrated and set up to
project to the left of the blade.
●
If you have any problem or question
on the laser guide, please call the
Service Center.
EXTENSION WING USE AND
ADJUSTMENT (FIG. 25)
The left and right side extension wings can
offer extra support for long workpieces.
1. Lift up on the locking lever (1) and
pull out the left extension wing to the
desired support length. Push down on
the locking lever (1) to tighten the
extension wing.
2. Repeat for the right side extension wing
if needed.
3. If the locking lever (1) will not tighten,
adjust the nut (2), located under the
base, 1/4 turn clockwise using a 10 mm
wrench until tight.
REPETITIVE CUTTING USING THE STOP
PLATE (FIG. 25)
The stop plate is designed for making
repetitive cuts of the same length.
NOTE:
Use only one stop plate at a time,
NEVER use both stop plates.
1. Rotate the stop plate (3) to vertical
position.
2. If stop plate will not rotate, loosen
the locking screw (4) 1/4 turn using a
screwdriver and 8 mm wrench.
Содержание SM2509R
