8
NOTE:
With the locking lever in the
down position, there must be sufficient
space between the lock nut (3) and the
stop plate (5) to allow the mechanism to
unlock. To increase the space, turn the
lock nut to the right.
TABLE SUPPORT ROD ADJUSTMENT
(FIG. 18)
1. Put the miter saw on a flat surface.
2. Check whether the miter saw is level
with the flat surface.
3. If not, loosen the nut (6) and turn the
table support rod (7) clockwise or
counterclockwise to adjust the height of
the table support rod (7) until the miter
saw is level with the flat surface.
4. Tighten the nut (6).
TURNING LASER GUIDE ON (FIG. 19)
1. To turn laser on, press on/off rocker
switch (1) to “ON” position.
2. To turn laser off, press on/off rocker
switch to “OFF” position.
ALIGNING THE LASER LINE
The laser line must always be correctly
aligned with the blade to ensure straight,
even cutting. Your tool is equipped with the
Laser Guide cutting guide using Class IIIa
laser line.
The laser line will enable you to preview the
saw blade path on the stock to be cut before
starting the miter saw. This laser guide is
powered by the transformed alternating
current supply directly through the power
lead. The saw must be connected to the
power source and the laser on/off switch
must be turned on for the laser line to show.
WARNING!
● AVOID DIRECT EYE CONTACT.
Laser radiated when laser guide is
turned on. Avoid direct eye contact.
Always un-plug the miter saw from
power source before making any
adjustments.
● NOTE: All the adjustments for the
operation of this machine have
been completed at the factory. Due
to normal wear and use, some
occasional readjustments may be
necessary.
● CAUTION: Use of controls or
adjustments or performance of
procedures other than those
specified herein may result in
hazardous radiation exposure.
● CAUTION: The use of optical
instruments with this product will
increase eye hazard.
● Do not attempt to repair or
disassemble the laser. If unqualified
persons attempt to repair this laser
product, serious injury may result.
Any repair required on this laser
product should be performed by
authorized service center personnel.
● Laser Warning Label:
Max. Output < 5 mW Wavelength:
630−660 nm, Complies with 21 CFR
1040.10 and 1040.11. Class IIIa Laser
Product. (FIG. 20)
● Laser Aperture Label:
AVOID EXPOSURE: Laser radiation is
emitted from this aperture. (FIG. 20)
LASER GUIDE ADJUSTMENT
(FIG. 21, 22, 23, 24)
NOTE:
All the adjustments for the operation
of this machine have been completed at
the factory. Due to normal wear and use,
some occasional readjustments may be
necessary.
A.
Checking Laser Line Alignment
(Fig. 21, 23)
1. Set the saw to a 0° miter and 0° bevel
setting.
2. Use a combination square to mark a 90°
angled running across the top and down
the front of a board. This line will serve
as the pattern line (Fig. 23) to adjust the
laser. Place the board on the saw table.
Содержание SM2509R
